Marshall electronic Official Manual for BC-0909-DA Universal Digital Converter - LCDRacks Support

Bracket Installation Feet Installation

BC-0909-DA Universal Digital Converter Users Guide

76 Operational Setup

1.Unpack the BC-0909-DA and accompanying V-PS6-1.2A power supply. Physically inspect for any damage that may have occurred during ship- ping. Also verify there is a small package with mounting accessories. Should there be any damage, immediately contact Marshall Electronics at 800-800-6608. If you are not located within the continental united states call +1 310-333-0606.

2.Install in your desired location. If wall mounting is required, attach the mounting brackets by removing the Phillips head screws on the sides, closest to the rear of the unit. (See Below) Only one screw per side should be removed.

Use the same screw to attach the bracket with the flange facing away from the side and parallel to the front of the BC-0909-DA metal case. The flange has two holes. For desktop use, apply the supplied rubber pads.

3.Connect required cables for signal input and output.

Please note that power must be applied to the BC-0909-DA for the Analog Output and HDSDI/SDI Loop out to be activated. All BNC connectors should be rated for 75Ω.

3.Plug the V-PS6-1.2A power supply into the A.C. source

4.Attach twist lock power connection from V-PS6-1.2A

power supply to the back of the unit.

5. Turn on the BC-0909-DA by depressing the power switch located on the front of the unit.

Refer to Page 4 picture for location of switch settings.

7Input Connectors

					Signal	HD Analog		SD Analog color	S-Video		HD or SD
					Type	color difference		difference	Y/C		Analog RGB
						YPbPr		Y, R-Y, B-Y			(Sync on Green)
					Pin1		Pr	R-Y	C		Red
					Pin2		Y	Y	Y		Green
					Pin3		Pb	B-Y			Blue
	HDSDI or SDI Out Re-		Analog Signals Out		Pin4
	HDSDI or SDI In		Refer to table below for
					Pin5
	Clocked and Shaped Signal
	Requires Power to be ap-		pin-out
					Pin6	Ground		Ground	Ground		Ground
	plied for activation
					Pin7	Ground		Ground	Ground		Ground
			6 VDC from		Pin8	Ground		Ground			Ground
			V-PS6-1.2A
					Pin9
			power supply
			Left Pin - Pos
			Right Pin- Neg
											HD-15
7	Switch Settings & Indicators									BNC Breakout
											Red
6
											Green
											Blue
		Input Signal Standard Indicator
		High Definition or Standard Definition
		Illuminates when SDI or
		HDSDI signal is present
											Ground
											Ground
											Ground
				Power On/Off indicator

Output Signal Format

Video- Only active in SD mode output Composite Video

YUV – Only active in SD mode output Component Video

Y-Pr-Pb – Only active in HD mode output Component Video

RGB – Active in HD and SD mode output RGB with Sync on Green Signal

78 Warranty

Marshall Electronics warranties to the first consumer, that this BC-0909-DA Digital to Analog Converter will, under normal use be free from defects in workmanship and materials, when received in its original container, for a period of one year from the purchase date.

This warranty is extended to the purchasing end user only and proof of purchase is necessary to honor the warranty. If there is no proof of purchase provided with a warranty claim, Marshall Electronics reserves the right not to honor the warranty set forth above. Therefore, labor and parts may be charged to you.

This warranty does not apply to product exterior and cosmetics. Misuse, abnormal service or handling, improper alterations or modifications in design or construction, voids this warranty. No sales personnel of the seller, nor any other person is authorized to make any warranties other than those described above, or to extend the duration of any warranties on behalf of Marshall Electronics, beyond the time period described above.

Due to constant effort to improve products and product features, specifications may change without notice.

1910 East Maple Ave. El Segundo, CA 90245 • Tel.: 800-800-6608 • Fax:310-333-0688 • www.LCDRacks.com • Email: sales@lcdracks.com