Marshall electronic V-LCD84SB-AFHD Specifications Installation and Initial Setup, Unpacking

Specifications

Installation and Initial Setup

■ PANEL

Screen Size	8.4” Diagonal
Display Area (h x v)	170.4 x 127.8 mm
Aspect Ratio	4:3 Native (4:3/16:9 Modes)
Pixels	800 x RGB x 600
Color Depth	24-bit (16,777,216 Colors)
Viewing Angle (h x v)	160° x 140°
Brightness	650 cd/m2
Contrast Ratio	600:1
Dot Pitch (h x v)	0.071 x 0.213 mm
Pixel Pitch (h x v)	0.213 x 0.213 mm
Pixel Response	25 ms (rise + fall)

■VIDEO INPUT/OUTPUT

Video Input / Output

Supports SMPTE 170M, NTSC/PAL

S-Video (Y/C) Input / Output Supports SMPTE 170M, NTSC/PAL

YPBPR Input / Output

Supports SMPTE 260M, 274M, 296M

HD-SDI Input / Output

Supports ITU-R BT.656, SMPTE 259M, 292M

VGA Input

Supports RGBHV, RsGsBs, RGsB, RGB CS

DVI Input

Supports Digital Signals Only (DVI-D) HDMI, HDCP Supported

■CONNECTORS

Video Input
Video	1 x BNC Female (75 Ω)
S-Video (Y/C)	1 x 4-Pin Mini-DIN
YPBPR	3 x BNC Female (75 Ω)
HD-SDI	1 x BNC Female (75 Ω)
VGA	1 x HD-15 Female
DVI	1 x DVI-I 29-Pin Female
Video Output (Active Loop-Through)
Video	1 x BNC Female (75 Ω)
S-Video (Y/C)	1 x 4-Pin Mini-DIN
YPBPR	3 x BNC Female (75 Ω)
SDI	1 x BNC Female (75 Ω)

Power Input

4-Pin XLR Male

Tally Interface

HD-15 Female

■TALLY

3 LEDs (Green, Red, Yellow). Activation requires contact closure of pin to ground on the HD-15 connector:

Pin No.	Signal
1	Green
2	Red
3	Yellow
4	Ground
5	Ground
6	N/C
7	N/C
8	N/C
9	N/C
10	N/C
11	N/C
12	N/C
13	N/C
14	N/C
15	N/C

■ ELECTRICAL
Power Consumption	2A @ 12VDC (24 W)
Voltage Requirement	12 VDC
V-PS12-5V-XLR Power Supply:
Input	100V-240V, 1.5A, 50-60Hz
Output	12VDC, 5A, 60W Max
V-Mount Battery Adapter
(Accepts standard 12V / 14.4V V-Mount Batteries)

■ MECHANICAL

Dimensions (w x h x d):	9.00” x 7.00” x 1.87”
Additional Mounting:	Desktop Stand and Rack Adapter
	Available
Weight (Monitor Only):	2.8 lbs
Operating Temperature	32°F to 120°F (0°C to 50°C)
Storage Temperature	-4°F to120°F (-20°C to 50°C)
Compliance	₠, FCC-Class A, ANSI-63.4
	(Certificates on file)
RoHs	Do not dispose. Return to
	Manufacturer or Authorized
	Recycle Facility.

■Unpacking

Carefully unpack the V-LCD84SB-AFHD monitor and verify that the following items are included:

•V-LCD84SB-AFHD Monitor

•V-PS12-5V-XLR Power Supply with 4-Pin XLR Connector

•Operating Instructions

Inspect the unit for any physical damage that may have occurred during shipping. Should there be any damage, immediately contact Marshall Electronics at (800) 800-6608. If you are not located within the continental United States, call +1 (310) 333-0606.

■Installation

The V-LCD84SB-AFHD monitor is shipped with a ¼”-20 mounting bracket on the bottom side, allowing the monitor to be flexibly mounted to a camera or other device using a variety of mounts. This ¼”-20 mounting bracket can also be attached to any side of the monitor.

Alternately, the V-LCD84SB-AFHD can be used in a desktop configuration with optional stands (Marshall part numbers V-ST08and V-STA84), or mounted in 19” inch rack with optional adapter (Marshall part number V-FR84).

¼”-20 Mounting Bracket can also be attached to any side of the monitor

V-LCD84SB-AFHD with optional desktop stand (Marshall Part Number V-ST08)

■Connections and Power-On

Plug the V-PS12-5V-XLR power supply into an AC power source (100-240 V @ 50/60 Hz). Attach the 4-pin XLR connector to the back of the monitor. Please note that 12VDC can be also supplied directly to the monitor from a variety of sources. The monitor will draw approximately 2 Amps at 12 Volts in operation.

Connect the required cables for video signal input and output. (Power must be applied to the V-LCD84SB-AFHD for the active loop-though outputs to be activated.) All BNC connectors are rated at 75Ω.

Turn on the unit by pressing the power button located on the front panel. Select a video input by pressing the corresponding input select button.

16 5