Marshall electronic V-R72P-2HDSDI warranty Product Overview, Features, Mechanical Specifications

1Product Overview

The Rack mounted and tiltable V-R72P-2HDSDIrepresents leading edge technology in LCD imaging for broadcast and professional video applications featuring High Resolution, megapixel, TFT screens with completely digital signal processing. All SMPTE/ITU digital video standards and signal types are accepted and displayed on each screen of this model. All video formats are scaled to fi t on screen in the highest resolution using a state of the art LSI that incorporates 4x4 pixel interpola- tions with precision Gamma correction to produce the best images available.

2 Features

• HDSDI (SMPTE292M/296M) With reclocked and shaped output
• SDI (SMPTE259M) (ITR-U601) With reclocked and shaped output
Remote control options (Available Summer 2005)
	3 RU
• Small Footprint – occupies only 3RU of a standard EIA 19 inch rack
	5.14”
• Ready to mount – all brackets are factory installed
	13.5 cm

•Lightweight – 75% lighter than CRT models

•All adjustments and selections are readily available. No menus!

•Settings memory restores active state with power off/on cycle

•Easy to use front panel selection of inputs

•NTSC or Pal operation with automatic signal format detection

•All inputs automatically terminate

•Built in color bar generator for each display

•Includes V-PS12-5V-1 Universal power supply (U.L. class 2)

•Three LEDs (Red, Green, Amber) produce 7 different tally indications

•Unique 180 degree tilt adjustment

•Dry erase label for each screen

4Mechanical Specifications

Dimensions	19.125”W x 2.5”D x 5.14”H (48.5cm x 6.35cm x 13.5cm)
V-R72P-2HD Weight	3.0lbs (2.27kg)
V-PS12-5V-1 Power Supply Weight	1 lbs (0.45kg)

5Operational Setup

1.Unpack the V-R72P-2HDSDI and accompanying V-PS12-5V-1 power supply. Physically inspect for any damage that may have occurred during shipping. Should there be any damage, immediately contact Marshall Electronics at 800-800-6608. If you are not located within the continental united states call +1 310-333-0606.

2.After inspection, install in your desired location of a standard EIA 19-inch equipment rack. Adequate ventilation is required when installed to prevent possible damage to the V-R72P-2HDSDI internal components.

3.Connect required cables for signal input and output.

Please note that power must be applied to the V-R72P-2HDSDI for all outputs to be activated. All BNC connectors should be rated for 75Ω.

4.Plug the V-PS12-5V-1 power supply into the A.C. source

5.Attach twist lock power connection from V-PS12-5V-1 power supply to the back of the unit.

6.Turn on the V-R72P-2HDSDI by depressing the power switch located on the front of the unit.

6Connectors

Analog and Digital Screen Formats and Frame Rates	V-PS12-5V-1
All signal types and frame rates are automatically detected	Universal power supply
	(U.L. class 2)

•525 –60i / 625 - 50i (Interlaced NTSC/PAL)

•720 x 486P (Progressive)

•720 x 576P (Progressive)

•720 x 1280 – Analog-50P, 59.94P, 60P /Digital 23.97P, 24P, 25P, 50P, 59.94P, 60P (Progressive)

•1035 x 1920 - 59.94i, 60i (Interlaced)

•1080 x 1920 – 50i, 59.94i, 60i / 23.973Psf, 24Psf, 25Psf, 29.97Psf, 30Psf

Psf=Progressive or Segmented Frame formats

3Electrical Specifications

*SDI inputs comply to SMPTE259M / ITU-R BT601

*HDSDI inputs comply to SMPTE292M,294M

*Active Outputs Require Power to be applied for activation

*Tally lamps active when connected to ground

Monitor 2

HDSDI or SDI In

Monitor 1

HDSDI or SDI In

Tally IN

DB-15 Female

Pin1-M2Yel	Pin9-
Pin2-M2Red	Pin10-
Pin3-M2Grn	Pin11-M1Yel
Pin4-	Pin12-M2Red
Pin5-Gnd	Pin13-M3Grn
Pin6-	Pin14-
Pin7-	Pin15-Gnd
Pin8-

Number of Screens	2
Screen Aspect	16:9 / 4:3 switchable
Display (Viewing Area)	7” (6.14”H × 3.27”V) (156.0mm x 83.28mm)
Viewing Angles	130 ̊H x 120 ̊V
Resolution (Dots)	800H×RGBx480V (1.2 million pixels)
Dot Pitch	0.065 mm (W) x 0.175 (H)
Pixel Response	<30ms
Contrast Ratio	400:1
Brightness (in cd/m²)	380 cd/m²
System	Digital
Inputs per display	HDSDI/SDI with re-clocked output (BNC)
Outputs per display	Active Composite loop through BNC
	Reclocked SDI loop through BNC
Color Bar Signal	Full field SMPTE
Power required	12 V D.C. from external U.L. Class 2 power supply (included) max 5.0 AMP
Power Consumption	24 Watt Nominal
Operating temperature	32 ̊F to 110 ̊F (0 ̊C to 45 ̊C)

Active Outputs require power	12 VDC from
to be aaplied	V-PS12-5V1
All input signals appear as	power supply
output signal	Left Pin - Pos
HDSDI/SDI signals are	Right Pin- Neg
reshaped and re-clocked
Analog output signals are
buffered and amplified

2 V-R72P-2HDSDI Users Guide Marshall Electronics 3