Maxxsonics TXi6008, TXi7508, TXi6408, TXi4008, TXi15080, TXi4408 Full Range Stereo, Full Range Mono

TXi4008 / TXi6008 2 CHANNEL AMPLIFIER APPLICATIONS

FULL RANGE STEREO

This is the most basic application for the TITAN Series 2 channel amplifiers.

1. Interconnect cable checklist:

Connect the LINE INPUTS to the Radio/CD with good quality RCA cables.

2. Crossover Switch:

The X-OVER switch must be in the FULL position.

3. Crossover frequency control checklist:

N/A for full range operation.

4. Line Level:

Refer to the section “Setting up systems after installation for best performance”.

NOTE: Minimum final loudspeaker impedances:

4 &-2-Ohms stereo mode or 4-Ohms mono mode

This amplifier will not do 1-Ohm stereo or 2/1-Ohm mono operation.

FULL RANGE
R	L	LINE
STEREO LINE INPUT		OUT
R	+ - HI	LINE INPUT
	gnd - + INPUT
	5V 0.2V	LEVEL
	0dB 12dB	BASS EQ
	60Hz 1.2KHz	HPF
	30Hz 250Hz	LPF
	FULL LPF HPF	X-OVER
	MONO STEREO	MODE

	+
SPEAKEROUTPUT	RIGHT	BRIDGE
	LEFT
	-
	+
	-
FUSE
POWER INPUT	GND REM +12V

FULL RANGE

SPEAKERS

TO BATTERY + 12 volts VIA FUSE

REMOTE TURN-ON

CHASSIS GROUND

FULL RANGE MONO

This application illustrates the basic mono bridging method for all Hifonics 2 channel amplifiers.

Interconnect cable checklist:

A MONO signal source is required, such as would be available from the mono sub bass output of an active crossover, whether stand alone, or built into a head unit or equalizer. Important: Do not be tempted to connect the hot, or positive outputs, from any source together to obtain a mono signal, as this could very well damage the output stage of that source.

It is necessary to feed the SAME signal to both left and right inputs via a Y-adapter RCA cable. Connect the mono speaker positive terminal to the RIGHT +, and its negative terminal to LEFT -.

Switch setting checklist:

- The AMPLIFIER X-OVER switch must be in the FULL position.

Crossover frequency control setting checklist:

N/A for full range operation.

TIP: If you are using the mono sub bass output of an active crossover, there is nothing wrong with switching in the low pass filter in these amplifiers for a steeper low pass roll- off.

Minimum final loudspeaker impedance: - 4-Ohms mono.

FULL RANGE

MONO LINE INPUT

VIA Y-ADAPTER

FROM MONO SOURCE

R	L	LINE
		OUT
R		LINE INPUT
HI INPUT	- gnd - +
5V 0.2V		LEVEL
0dB 12dB		BASS EQ
60Hz 1.2KHz		HPF
30Hz 250Hz		LPF
FULL LPF HPF		X-OVER
MONO STEREO		MODE

	+
SPEAKEROUTPUT	RIGHT	BRIDGED	FULL RANGE
	LEFT
	-
	+		MONO SPEAKER
	-
FUSE
POWERINPUT	REMGND +12V		TO BATTERY + 12 volts VIA FUSE
			REMOTE TURN-ON
			CHASSIS GROUND

The HIGH LEVEL inputs are used when the radio/CD player does not have RCA cable outputs. You can connect the radio/CD player speaker wires directly

to the amplifier via the high Level Inputs.	Use this connector for 2 CH amplifiers	Use both connectors for 4 CH amplifiers
	GRAY: CH 1 Speaker Input +	ORANGE: CH 3 Speaker Input +
	BROWN: CH 1 Speaker input -	PINK: CH 3 Speaker input -
	Black: Chassis Ground	Black: Chassis Ground
	GREEN: CH 2 Speaker Input -	BLUE: CH 4 Speaker Input -
	White: CH 2 Speaker Input +	YELLOW: CH 4 Speaker Input +

3