Maytag MGC7430W, MGC7636W specifications Product Model Numbers, Location Requirements, Electrical

30" (76.2 cm) and 36" (91.4 cm) Gas Built-In Cooktop

PRODUCT MODEL NUMBERS		LOCATION REQUIREMENTS
MGC7430W	MGC7630W	IMPORTANT: Observe all governing codes and ordinances. Do not
MGC7536W	MGC7636W	obstruct flow of combustion and ventilation air.
Electrical		● It is the installer’s responsibility to comply with installation clearances
● A 120 volt, 60 Hz, AC only, 15-amp, fused electrical circuit is required. A		specified on the model/serial rating plate. The model/serial rating plate is
time-delay fuse or circuit breaker is also recommended. It is		located on the underside of the cooktop base.
recommended that a separate circuit serving only this cooktop be
provided.
Type of Gas			A
Natural Gas: This cooktop is design-certified by CSA International for
use with Natural gas or, after proper conversion, for use with LP gas.
● This cooktop is factory set for use with Natural gas. If converting to LP
gas, see the “LP Gas Conversion” instructions provided in the package
containing literature. The model/serial rating plate located on the
underside of the cooktop base has information on the types of gas that		A. Model/serial rating plate
can be used. If the types of gas listed do not include the type of gas
available, check with the local gas supplier.		● To eliminate the risk of burns or fire by reaching over heated surface
LP Gas Conversion: Conversion must be done by a qualified service		units, cabinet storage space located above the surface units should be
technician.		avoided. If cabinet storage is to be provided, the risk can be reduced by
No attempt shall be made to convert the cooktop from the gas specified		installing a range hood that projects horizontally a minimum of 5"
		(12.7 cm) beyond the bottom of the cabinets.
on the model/serial rating plate for use with a different gas without
		● The cooktop must be a specified cooktop that is approved to be installed
consulting the serving gas supplier. See the Gas Conversion instructions
provided in the package containing literature.		either alone or over an undercounter built-in oven. Check the cooktop
Gas Supply Line		base approved installation label for your cooktop model number and
		approved combinations of cooktops and ovens that can be installed. If
● Provide a gas supply line of ³⁄₄" (1.9 cm) rigid pipe to the cooktop
		you do not find this label, your cooktop may not be approved for use
location. A smaller size pipe on longer runs may result in insufficient		over an undercounter built-in oven. Contact your dealer to confirm that
gas supply. Pipe-joint compounds that resist the action of LP gas must		your cooktop is approved.
be used. Do not use TEFLON®† tape. With LP gas, piping or tubing size		● Ovens approved for this type of installation will have an approval label
should be ¹⁄₂" minimum. Usually, LP gas suppliers determine the size		located on the top of the oven. If you do not find this label, contact your
and materials used in the system.
		dealer to confirm that your oven is approved. Refer to oven
Flexible metal appliance connector:		manufacturer’s Installation Instructions for approval for built-in
● If local codes permit, use a ¹⁄₂" or ³⁄₄" I.D. flexible stainless steel tubing		undercounter use and proper cutout dimensions.
gas connector, designed		● The cooktop should be installed in a location away from strong draft
by CSA to connect the		areas, such as windows, doors and strong heating vents or fans.
cooktop to the rigid gas		● All openings in the wall or floor where cooktop is to be installed must be
supply line.		sealed.
● A ¹⁄₂" male pipe thread is needed for connection to the female pipe
		IMPORTANT: To avoid damage, check with your builder or cabinet
threads of the inlet to the cooktop pressure regulator.
		supplier to make sure that the materials used will not discolor, delaminate
● Do not kink or damage the flexible metal tubing when moving the
		or sustain other damage.
cooktop.		Mobile Home - Additional Installation Requirements
Rigid pipe connection:
		The installation of this cooktop must conform to the Manufactured Home
The rigid pipe connection requires a combination of pipe fittings to obtain
		Construction and Safety Standard, Title 24 CFR, Part 3280 (formerly the
an in-line connection to the cooktop.		Federal Standard for Mobile Home Construction and Safety, Title 24, HUD
The rigid pipe must be level with the		Part 280). When such standard is not applicable, use the Standard for
cooktop connection. All strains must		Manufactured Home Installations, ANSI A225.1/NFPA 501A or with local
be removed from the supply and fuel		codes.
lines so cooktop will be level and in		In Canada, the installation of this cooktop must conform with the current
line.
		standards CAN/CSA-A240-latest edition, or with local codes.

●Must include a shutoff valve:

The supply line must be equipped with a manual shutoff valve. This valve should be located in the same room but external to the cooktop opening, such as an adjacent cabinet. It must be accessible without removing the cooktop, and it should be in a location that allows ease of opening and closing. Do not block access to shutoff valve. The valve is for turning on or shutting off gas to the cooktop.

	B
A	A. Gas supply line
	B. Shutoff valve “open” position
	C. To cooktop
	C
†®TEFLON is a registered trademark of E.I. Du Pont Nemours and Company.
	Page 1 of 2

Because Whirlpool Corporation policy includes a continuous commitment to improve	Dimensions are for planning purposes only. For complete details, see Installation	Ref. W10526090A
our products, we reserve the right to change materials and specifications without notice.	Instructions packed with product. Specifications subject to change without notice.	7/9/13