| Troubleshooting• Make sure the lid is completely closed. |
| ||
|
| |||
| Won’t Fill | • | Plug cord into live electrical outlet. |
|
|
| • | Check fuse or reset circuit breaker. |
|
|
| • | Turn the control dial to proper cycle and restart the washer. |
|
|
| • | Turn both faucets on fully. |
|
|
| • | Straighten inlet hoses. |
|
|
| • | Disconnect hoses and clean screens. Hose filter screens may be plugged. |
|
| Won’t Agitate | • | Check fuse or reset circuit breaker. |
|
|
|
| ||
|
| • | Turn the control dial to proper cycle and restart the washer. |
|
|
| • | Pauses are normal. Wait and see if the washer will start again. |
|
|
|
|
|
|
| Won’t Spin | • | Check fuse or reset circuit breaker. |
|
| or Drain | • | Straighten drain hoses. Eliminate kinked hoses. If there is a home drain restriction, call for |
|
|
|
| drain service. |
|
|
| • | Close lid and restart the washer. For your safety, washer will not spin unless the lid is closed. |
|
|
| • | Suds lock – caused by too many suds. Rewash without detergent. Use correct amount of a |
|
|
|
|
| |
|
|
|
|
|
| Load is Wet | • | Unevenly distributed load. Redistribute the load, close the lid and restart the washer. Check for |
|
|
|
| leveling. Be sure water level is acceptable for load size. |
|
|
| • | A fast spin speed (or Normal agitation) is recommended for heavy loads like jeans or towels. |
|
|
|
|
|
|
| Stops | • | Plug cord into live electrical outlet. |
|
|
| • | Check fuse or reset circuit breaker. |
|
|
| • | Close lid and restart the washer. For your safety, washer will not agitate or spin unless lid is closed. |
|
|
| • | This may be a pause in the cycle. Wait briefly and it may start. |
|
|
|
|
|
|
| Leaks Water | • | Make sure hose connections are tight. |
|
|
| • | Make sure end of drain hose is correctly inserted and secured to drain facility. |
|
|
| • | Avoid extended soaking – soak for 30 minutes or less. |
|
|
| • | Avoid overloading. |
|
|
|
|
|
|
| Is Noisy | • | Be sure washer is leveled properly as outlined in installation manual. |
|
|
| • | Weak floors can cause vibration and walking. |
|
|
| • | Operating sounds will vary depending on agitation speed. |
|
|
|
|
|
|
| Fills with | • | Turn both faucets on fully. |
|
| the Wrong | • | If equipped with a temperature selector dial, be sure it is set directly on a temperature setting and |
|
| Temperature |
| not between settings. |
|
| Water | • | Make sure temperature selection is correct. |
|
|
|
| ||
|
| • | While the washer is filling, you may notice just hot and/or just cold water entering the tub when |
|
|
|
| cold or warm wash temperatures are selected. |
|
|
| • | Make sure hoses are connected to correct faucets and inlet connections. Be sure water supply is |
|
|
|
| regulated correctly. Flush water line before filling washer. |
|
|
| • | Check the water heater. It should be set to deliver a minimum 120° F (49° C) hot water at the tap. |
|
|
|
| Also check water heater capacity and recovery rate. |
|
|
| • | Disconnect hoses and clean screens. Hose filter screens may be plugged. |
|
|
|
|
|
|
| Cycle Selector | • | Extra Rinse (select models) is selected. |
|
| Advances Through |
|
|
|
| Off |
|
|
|
|
|
|
|
|
4
