OPTION SELECTIONS
OPTIONS | DISH LOAD TYPES | DESCRIPTIONS | USE WITH: | ||
|
|
|
|
|
|
Heated dry | Heated dry: For best | Turn OFF when loads contain plastic dinnerware that may be | Heavy, Normal, Light, or | ||
|
|
| drying results, dry dishes | sensitive to high temperatures. | Auto Clean Plus |
|
|
| |||
|
|
| with heat. | This option with the use of rinse aid will provide the best |
|
|
|
|
|
| |
|
|
|
| drying performance. |
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
| To sanitize your dishes and | Raises the water temperature in the final rinse to | Heavy, Normal, Light, or |
|
|
| glassware in accordance | approximately 154°F (68°C). This high temperature rinse | Auto Clean Plus |
|
|
| with NSF/ANSI Standard | sanitizes your dishes and glassware in accordance with |
|
|
|
| 184 for Residential | NSF/ANSI Standard 184 for Residential Dishwashers. |
|
|
|
| Dishwashers. | Certified residential dishwashers are not intended for |
|
|
|
|
| licensed food establishments. |
|
|
|
|
| The Sanitize option adds heat and time to the cycle. |
|
|
|
|
|
|
|
|
|
| To run your dishwasher at | Delays the start of a cycle up to 6 hours. | All cycles |
|
|
| |||
|
|
| a later time or during off- | Select a wash cycle and options. Press Delay. Press START/ |
|
|
|
| peak hours. |
| |
|
|
| RESUME. Close the door firmly within 3 seconds. For fully |
| |
|
|
|
|
| |
|
|
|
| integrated models ((controls on top of console). |
|
|
|
|
|
|
|
Control Lock To avoid unintended use of your dishwasher, or cycle
and option changes during a cycle.
To turn on Lock, press and hold Heated Dry for at least | Anytime |
3 seconds. |
|
To turn off Lock, press and hold Heated Dry for at least |
|
3 seconds. |
|
When Control Lock is lit, all buttons are disabled. If you press |
|
any pad while your dishwasher is locked, the light flashes |
|
5 times. The dishwasher door can be opened while the |
|
controls are locked. |
|
IMPORTANT: The sensor in your dishwasher monitors the soil level. Cycle time and/or water usage can vary as the sensor adjusts the cycle for the best wash performance. If the incoming water is less than the recommended temperature or food soils are heavy, the cycle will automatically compensate by adding time, heat and water as needed.
CONTROLS AND
CYCLE STATUS
CONTROL PURPOSE | COMMENTS |
To start or resume a wash cycle
If the door is opened during a cycle or the power is interrupted, all lights will flash to indicate a suspended cycle. The cycle will not resume until the door is closed, and the START/RESUME button is pushed.
To cancel wash | Close the door firmly. The dishwasher starts a |
cycle | drain completely. |
To follow the progress and status of your dishwasher cycle
The “Clean” indicator glows when a cycle is finished.
If you select the Sanitize option, when the Sanitize cycle is finished, the Sanitized indicator glows. If your dishwasher did not properly sanitize your dishes, the light will be blinking. This can happen if the cycle is interrupted, or the water could not be heated to the required temperature. The clean and sanitize lights go off when the door has been opened for more than 30 seconds or the CANCEL key is pressed.
The “Washing” indicator glows at the start of the first fill of any cycle (except Rinse Only) and remains on until the end of the main wash cycle.
The “Drying” indicator glows during the drying portion of each cycle (except Rinse Only).
6