UK
CARBURETTOR
ADJUSTMENTG
We suggest carburetor adjustments are made by an authori- zed servicing dealer.
The carburetor has three adjustment screws:
•L: The needle screw L governs the fuel flow at low speed and also the acceleration from low to full speed.
To set screw L: close screw L turning it clockwise without forcing.
Then open screw 1 full turn (counterclockwise) .
If acceleration is not smooth, open another 1/8 turn to increase fuel flow .
•H: The needle screw H governs fuel flow at high speed (throttle valve fully open).
To set hi speed screw H: close screw H turning it clockwi- se without forcing .
Then open screw 1 full turn (counterclockwise) .
If the engine speed is too high, open the screw about 1/8 turn (counterclockwise). Optimal adjustment is found between 1 and 1 1/4 turns.
•I: The I (IDLE) screw controls the throttle opening to govern idle speed (2800
CAUTION: increased idle speed may cause chain movement. The carburetor is adjusted for normal operation during produc- tion. When considerable changes of altitude require a supple- mentary adjustment, contact an authorised service station which offers the latest in tools, parts and technical assistance.
ROUTINE MAINTENANCE | H |
Ensure engine is always switched off before any kind of maintenance operation.
CHAIN: Check tension regularly. A new chain will require more frequent adjustment. Loosen retention nuts. Tighten chain (see assembly instructions). Tighten retention nuts and adjust.
1BAR
–Clean the bar groove (K) and check the lubrication holes (L) in the bar to ensure that they are not clogged.
–Grease sprocket periodically. Rotate sprocket and repeat.
–Rotate bar periodically to maximise bar life.
2AIR FILTER
–A dust clogged air filter may cause carburetor problems. This may prevent the engine from reaching its maximum r.p.m. and cause high fuel consumption.
–Remove cover.
–Wash filter in petrol (do not use fuel which is mixed with oil).
–The filter can also be cleaned with compressed air.
–Replace filter if damaged or if it does not seal tightly in the air box.
3SPARK PLUG
Remove and clean the spark plug every 30 hours. Check the electrode gap (0,5/0,6 mm. - 0.025 inches).
–Replace spark plug about every 100 working hours or whenever it is extremely encrusted.
–Heavily encrusted electrodes can result from an incorrect carburetor setting or from wrong fuel mixture (too much oil in the fuel mix) or a poor quality of oil in the fuel mix. Check and correct.
4OIL FILTER
The oil filter is on the end of the oil suction hose inside the oil tank.
To clean and replace the filter pull it out through the oil tank filter opening. Use a piece of bent wire or long forceps.
To remove deposits from the oil tank
Never use waste oil.
5FUEL FILTER
To change fuel filter remove the tank cap and pull out the filter with a piece of bent wire or long forceps. Replace the filter as shown in the illustration and reposition it.
It is recommended to replace the fuel filter at least once a year.
CHAIN BRAKE
–WARNING: Contact your service dealer if anything appears wrong with your chain brake. Do not disassem- ble or manipulate the mechanism of the chain brake.
–Clean the brake mechanism periodically (without disas- sembling it) and control the wear of the band visually.
•PERIODICALLY: It is important to clean the saw thoroughly particularly around cylinder fins to avoid overheating of the engine.
•LONG STORAGE: Empty fuel and run engine until dry.
SAFETY CHAIN BRAKE | I |
Your chain saw is fitted with a safety chainbrake desi- gned to stop the chain in milliseconds in case of kick- back. Always hold the saw firmly in both hands.
The chain brake does not provide a total protection if the machine is used without taking the necessary precautions and maintenances.
The chain brake is intended to engage automatically in case of kickback.
The chain brake can also be engaged manually by pushing the chain brake lever forwards.The manual use of the chain brake is recommended only at idle.
Always test the chain brake before using your saw. Do this by engaging the brake at idle (see below).
Always release the brake before starting.
Kickback may occur if the end of the bar (see illustrated angle) touches any solid object.
Never attempt to start a cut with the end of the bar. Kickback is a violent upward and rearward movement of the bar and may cause you to lose control of the machine. Therefore you should avoid starting a cut with this part of the bar. Always keep a firm grip on the saw with both hands because, in case of kickback, it is the contact of the left hand with the brake lever which will help to engage the brake.
CHAIN BRAKE TESTING:
1The chain brake (A) is disengaged when brake lever is pul- led back and locked(chain can move).
4
