USE

Place appliance on back (like a rucksack) and adjust shoulder straps and belt to suit.

a.Adjust shoulder straps using buckles at top and bottom.

b.Fasten belt around waist using the Velcro fastening.

NOTE: Check position of on/off button (25) for quick access in event of emergency. The on/off button is at the bottom of the left side of the appliance when you have it on.

Plug in and switch the power on.

Press the on/off button to start and stop the appliance.

While in use, the suction force can be regulated by opening and closing the air valve (3) on the handle.

a.When the vent closes full suction is achieved. This is the normal setting.

b.When the vent opens, more air is allowed in, reducing suction power at the floor nozzle. This function is for cleaning curtains and other light items which can get sucked into the nozzle.

The floor nozzle bristles have two settings which can be selected using the brush function button on top of the nozzle.

a.When cleaning hard surfaces (stone flooring, tiles, etc.), the nozzle brushes should be extended.

b.When cleaning carpets and rugs, the brushes should be retracted into the nozzle.

If vacuum strength drops during use, check dust bag (see Replacing Dust Bag below).

If full suction is not restored, by replacing bag, check hose or nozzle for blockage, or motor filter bag/filter could be dirty.

NOTE: Check cause of fault and correct. Do not use appliance if any air holes are blocked. Permanent motor damage can result.

Tips for vacuum cleaning

Use holsters on front of belt for accessories to ensure they are always handy.

Each nozzle has a special purpose. Try each of them out in different situations.

When appliance is not on your back, carry using the carrying handle. NOTE:

Never pull or lift the appliance by the cord.

Hose can be fitted to right or left side depending on which hand you want to use. Remove and turn lid to switch side (see Motor Filter Bag, Dust Bag and Lid above).

Switch appliance function between blow and suck by moving hose.

oNOTE: The appliance will never blow dust and dirt out – only filtered air – as all the filters and dust bag will still be correctly fitted.

oTo use as a blower instead of vacuum cleaner, change air flow as follows:

a.Disconnect power, place appliance on floor.

b.Remove hose by turning clockwise and detaching from connector.

c.Remove exhaust filter (see Replacing Exhaust Filter below).

d.Take filter pad out of filter and place in exhaust hole.

e.Fit exhaust connector over filter pad, with the studs in the bottom fitting into the holes in the bottom edge of the hole.

f.Press into place fitting the stud in the top of the connector under the release button with a click.

g.Fit hose to connector (see Fitting Hose and nozzle above).

h.Remember to switch hose back to normal position and replace exhaust filter in exhaust hole when finished with blowing function.

CHANGING THE DUST BAG

If the appliance loses suction strength during use, the dust- or motor filter bag can be dirty, and need replacing. Both bags are in the internal compartment (6).

NOTE: Never use the appliance if the bag is full or with no dust- and motor filter bag at all.

Disconnect power, place appliance on floor.

Remove hose by turning clockwise and detaching from connector.

Open lid by pressing in the two lock studs on the sides and pulling upwards.

Tip dust bag in lid upwards by pulling the curved edge on side of dust bag holder.

Carefully extract bag from holder away from lid.

Place bag carefully in refuse bin. Make sure that there are no holes in it. Do not fold or press the bag.

Insert a new dust bag in holder.

Click holder into place, check bag is secure and facing the right direction.

Pull motor filter bag out of appliance and clean (see Cleaning below).

Replace motor filter bag, check rubber edge of bag fits properly all the way round.

Replace lid, ensuring that it will allow the hose connector to be on the side you want (depending on which hand you will use to operate the vacuum cleaner with).

Press lid down until both lock tabs click into place.

We recommend cleaning the motor filter bag at least twice a year, or whenever it is dirty.

REPLACING EXHAUST FILTER

Used to filter exhaust air from the appliance. The appliance must not be used if there is no exhaust filter fitted.

Remove the exhaust filter by pressing down the release button and pulling the filter out.

Remove the filter pad, replace or clean as described under Cleaning below.

Replace filter pad in filter and replace in appliance. Close it locks into place with

a click.

We recommend replacing the filter pad after 4 to 6 months’ use, when it becomes dirty, or if the appliance’s suction strength is reduced.

STORAGE

Before storing, roll cord up without bending it.

Store in a cool dry place. Do not place heavy objects on top of the appliance.

Straps and harness need not be removed, but check they are secure when using it next.

CLEANING

Clean the appliance by wiping it with a damp cloth.

Do not use any form of solvent, or strong or abrasive cleaning agent.

Make sure all filters are kept clean (see above).

oShake and beat the filter pad carefully to remove dust and dirt. o Pad can be washed carefully in warm water.

o Check it is completely dry before replacing in the appliance. NEVER replace a filter pad wet.

oReplace filter pads with the same type when worn or cannot be cleaned properly.

oRemove motor filter bag (see Replacing Dust Bag below).

oTurn bag upside down, hold handle under bottom and shake hard. o Replace bag in appliance.

INFORMATION ON DISPOSAL AND RECYCLING OF THIS PRODUCT

Please note that this Adexi product is marked with this symbol: This means that this product must not be disposed of together with ordinary household waste, as electrical and electronic waste must be disposed of separately.

In accordance with the WEEE directive, every member state must ensure correct collection, recovery, handling and recycling of electrical and electronic waste. Private households in the EU can take used equipment to special recycling stations free of charge. In certain member states, used appliance can be returned to the dealer where they were bought on the condition you buy new products. Contact your retailer, distributor or the municipal authorities for further information on what you should do with electrical and electronic waste.

GUARANTEE TERMS

The guarantee does not apply:

if the above instructions are not followed

if the appliance has been interfered with

if the appliance has been mishandled, subjected to rough treatment, or has suffered any other form of damage

if faults have arisen as a result of faults in your electricity supply.

Due to the constant development of our products in terms of function and design, we reserve the right to make changes to the product without prior warning.

QUESTIONS AND ANSWERS

If you have any questions regarding use of the appliance and cannot find the answer in this user guide, please try our website at www.adexi.eu.

Go to the "Consumer Service" menu, click on "Question & Answer" to see the most frequently asked questions.

You can also see contact details if you need to contact us for technical issues, repairs, accessories and spare parts.

IMPORTER

Adexi Group

www.adexi.eu

We cannot be held responsible for any printing errors.

12

Page 12
Image 12
Melissa 240-006 manual Use, Changing the Dust BAG, Replacing Exhaust Filter, Storage, Cleaning, Guarantee Terms, Importer

240-006 specifications

Melissa 240-006 is an advanced robotic system designed for a range of applications in various industries, showcasing a variety of cutting-edge features and technologies. This innovative machine is engineered to enhance operational efficiency while providing reliable performance across many tasks.

One of the main features of the Melissa 240-006 is its high-precision robotic arm, which is capable of executing intricate movements with remarkable agility. The arm's advanced articulation allows it to access tight spaces, making it ideal for tasks in manufacturing, assembly, and even healthcare settings. The versatility of the robotic arm enables it to pick, place, and manipulate objects of different weights and sizes, adapting seamlessly to a broad array of activities.

The Melissa 240-006 is equipped with state-of-the-art sensor technology that enhances its environmental awareness. This array of sensors includes cameras, LiDAR, and ultrasonic sensors, allowing the robot to perceive and navigate its surroundings effectively. These sensors enable the system to avoid obstacles, assess distances, and recognize objects, facilitating safe and efficient operation in dynamic environments.

Another distinguishing characteristic of the Melissa 240-006 is its artificial intelligence capabilities. Powered by advanced machine learning algorithms, this robotic system can learn from its experiences over time, optimizing its performance based on previous interactions. This intelligence allows for improved decision-making, which is crucial in complex tasks requiring adaptability and a level of autonomy.

Connectivity is a significant aspect of the Melissa 240-006, as it supports seamless integration with existing manufacturing and operational systems. Utilizing IoT technology, the robot can communicate with other devices and systems, allowing for real-time data sharing and coordination. This connectivity not only enhances efficiency but also opens the door for remote monitoring and control, providing users with greater flexibility in managing their operations.

Moreover, the Melissa 240-006 is designed with user-friendliness in mind. Its intuitive interface allows operators to program and control the robot with minimal training, making it accessible for a wide range of users. Additionally, the modular design facilitates easy maintenance and upgrades, ensuring that the system remains at the forefront of technological advancements.

In summary, the Melissa 240-006 embodies the future of robotics with its combination of precision, advanced sensing, artificial intelligence, and connectivity features. As industries continue to embrace automation, the Melissa 240-006 stands out as a valuable tool of productivity, adaptability, and efficiency in the modern workspace.