UK
INTRODUCTION
To get the best out of your new apparatus, please read this user guide carefully before using it for the first time. Take particular note of the safety precautions. We also recommend that you keep the instructions for future reference.
IMPORTANT SAFETY PRECAUTIONS
•Connect to 230 V, 50 Hz only. The guarantee is not valid if it is connected to the wrong voltage.
•The apparatus may only be used for its original purpose. Do not use for drying towels, clothes, etc. Not for commercial use not for heating building sites, greenhouses, barns, etc.
•Handle with care. The quartz tubes in the heating head are fragile. Avoid subjecting to heavy impact. Do not remove the grille. If necessary to clean the heating head inside, contact a professional.
•The appliance should be set up or mounted in accordance with the instructions in section “Positioning of the appliance” below.
•The appliance is high powered and can emit very intense heat. Do not expose animals or small children to direct heat from the appliance.
•The appliance must never be mounted or used in the vicinity of flammable objects, e.g. curtains, furniture, etc. It must not be set up or mounted close to wall sockets or in wet or damp environments (in bathrooms, by swimming pools, etc.).
•Do not use the appliance outdoors in wet weather!
•In order to reduce the risk of fire or electric shock, never use the appliance together with an electronic timer or device which turns on and off the appliance automatically.
•Do not cover.
•Do not cover or block the remote control receiver. This will prevent the signal being received.
•Ensure that the cable does not get caught beneath the appliance, behind shelves etc. Do not run the cable under carpets etc. Place the cable so that it is not possible to trip over it, and avoid wrapping it around the stand (only models with base) or heater head.
•If use of an extension cable is required with the appliance, then the extension cable should have a minimum rating of 10A and 2000W. If a cable reel is used, then it should be unrolled entirely.
•Do not submerge in any form of liquid.
•Never insert your fingers, pencils or other objects through the grille. The grille will become hot during use and must not be touched until the appliance has cooled down.
•Keep an eye on any children in the vicinity of the apparatus when it is in use. Children must not be allowed to use the apparatus unless supervised by an adult.
•Switch off before moving or cleaning the appliance.
•Never try to repair the apparatus yourself. If the apparatus, cable or plug needs to be repaired, it should be taken to an authorised service centre. Unauthorised repairs or modifications to the appliance will invalidate the guarantee. Please contact the store where you bought the appliance for repairs under guarantee.
KEY TO MAIN COMPONENTS OF THE APPARATUS
1.Heating head
2.Grille
3.Function indicator
4.Receiver for remote control signal
5.String
6.Power cord
7.Stand (only for model with base)
8.Clip
9.Wall mounting bracket
10.Mounting screw
11.Remote control
Stand components (only for models with base)
a.Base
b.Stand, lower part
c.Washer and screw
d.Stand, middle part
e.Stand, upper part
f.Screws (x2)
g.Sleeve
h.Collar
i.Thin rod
A mounting wall bracket together rawlplugs and screws are included with the
POSITIONING THE APPLIANCE
Wall-mounted model (670-202)
•The heater head (1) should be at least 30cm from the ceiling, 50cm from any side wall, and at least 1.8m above the floor.
•Mount using the included wall bracket, do not use other brackets or fittings.
•The angled section of the bracket should face upwards.
•Hang the heater head on the wall bracket. The mounting bracket on the upper part of the rear of the heater head should hang in the angled part of the wall bracket, and the
mounting screws (7) should be placed in the holes at the bottom of the wall bracket and pressed down, until the heater head is firmly fixed.
•Check that the appliance is firmly fixed in place before using it.
Model with stand
•The appliance should be sited at least 1m from the nearest wall. The heater head should be at least 30cm from the ceiling, and at least 1.8m above the floor. The appliance should stand firmly on a horizontal floor.
•Put the lower part of the stand (b) in the base (a), lay the base on its side, and fasten the stand to the underside of the base with the washer and screw (c).
•Position the base correctly so that the stand is upright. Slacken screw
(f)in the middle of the stand (d), and insert the middle part into the lower part. Align the crew with the recess in the lower part. Tighten the screw.
In the same way, fix the upper part of the stand
(e)in the middle part with a screw.
•Insert the thin rod (h) in the sleeve (g) on the upper end of the stand. Pass the collar (h) down over the thin rod and screw firmly onto the sleeve.
•Mount the heating head on the thing rod so that the hole in the rod is aligned with the hole in the head. Secure using mounting screw (10). Tighten all screws thoroughly.
•Check that the appliance is standing firmly in place before using it.
•The cable may be secured in the cable holder on the stand.
•The curved stand can be rotated 360° so that the heating head can face in any direction.
10
