Mellerware 8 5 3 0 0 Instructions for blender, Instructions for beater, Using Your Blender

Important Safeguards

Before using the electrical appliance, the following basic precautions should always be followed:

1.Read all instructions.

2.Before using check that the voltage of wall outlet correspond to the one shown on the rating plate.

3.Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions, or is

4.dropped or damaged in any manner. Return appliance

5.to the nearest authorized service facility for examination, repair or electrical or mechanical adjustment.

6.If the supply cord is damaged it must be replaced by the manufacturer or a authorized service agent or a qualified technician in order to avoid a hazard.

7.Unplug from outlet when not in use, before putting on or taking off parts, and before cleaning.

8.Do not let cord hang over edge of table or hot surface.

9.Do not immerse upper part of blender into water as this would give rise to electric shock.

10.Close supervision is necessary when your appliance is being used near children or infirm persons.

11.Avoid contacting moving parts.

12.Keep hands and utensils out of container while blending to reduce the risk of severe injury to persons or damage to the blender.

13.A scraper may be used only when the blender is not

14.running.

15.The appliance cannot be used for chopping ice or blending hard and dry substance, otherwise the blade could blunt.

16.To reduce the risk of injury, never place cutting blade on base without first putting bowl properly in place.

17.Be sure chopper lid is securely locked in place before operating appliance.

18.The use of accessory not recommended by the manufacturer may cause injuries to persons.

19.Do not operate the appliance for other than its intended use.

20.Do not use outdoors.

SAVE THESE INTRUCTIONS

Using Your Blender

Before the first use, clean the blender according to the section of “quick cleaning”. The time running unit without load can’t exceed 15 seconds.

Important: Blades are very sharp, handle with care Ensure that the hand-held stick blender is unplugged from the power outlet before assembling or removing attachments.

Instructions for blender

Max operation duration under high speed per time cannot exceed 1 minute, and 1 minute rest time must be maintained at two consecutivecycles.

1.To assemble the detachable shaft with the motor

unit, turn the shaft in an anti-clockwise direction until tightened. To disassemble, just turn in the adverse direction.

2.Simply plug the hand-held blender to power outlet.

3.Lower the hand-held blender into food and depress the switch at the top of the motor unit.

4.To stop the hand-held blender release the switch at the top of the motor unit.

Instructions for chopper

1.Max operation duration under high speed per timecannot exceed 1 minute, and 1 minute rest time must bemaintained at two consecutive cycles.

2.Place the chopper bowl on a clean, level surface.

3.Assemble the stainless steel blade into the chopper bowl, as shown in Fig.1.

4.Place food into the chopper bowl.

5.Note: remove the bones from meat, cut into small pieces, then place into bowl, the max quantity of product can’t exceed 200g with each blend.

6.Attach the Lid onto the chopper bowl and turn it ina clockwise direction until it locks into position. (see Fig.2) To detach the lid, turn in adverse direction.

7.Insert the bottom part of the blender into the hole of the chopper lid, and turn in clockwise direction to lock. (See Fig.3)

8.Plug the appliance to power outlet and depress the switch to begin operation.

9.To stop the appliance release the switch at the top of the motor unit.

Caution:

•To reduce the risk of injury, never place cutting blade on base without first putting bowl properly in place.

•Be sure chopper lid is securely locked in place before operating appliance.

Fig.1 Fig.2 Fig.3

Instructions for beater

1.Max operation duration under high speed per time cannot exceed 3 minute, and 1 minute rest time must be maintained at two consecutive cycles.

2.To assemble the beater with the motor unit, turn the whisk anti-clockwise direction until tightened.

3.To disassemble, just turn in the adverse direction.