
Regulatory Approvals
•FCC Class A •UL 1950
•CSA C22.2 No. 950 •EN60950
•CE
•– EN55022 Class B •–
Canadian EMI Notice
This Class A digital apparatus meets all the requirements of the Canadian
Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.
European Notice
Products with the CE Marking comply with both the EMC Directive (89/336/EEC)
•
and the Low Voltage Directive (73/23/EEC) issued by the commission of the European Community. Compliance with these directives implies conformity to the following European Norms:
•EN55022 (CISPR 22) - Radio Frequency Interference
Five Year Warranty
MiLAN Technology warrants to the original consumer or purchaser that each of its products, and all components thereof, will be free from defects in material and/or workmanship for a period of five years from the original factory date. Any warranty hereunder is extended to the original consumer or purchaser and is not assignable. MiLAN Technology makes no express or implied warranties including, but not limited to, any implied warranty of merchantability or fitness for a particular purpose, except as expressly set forth in this warranty. In no event shall MiLAN Technology be liable for incidental or consequential damages, costs, or expenses arising out of or in connection with the performance of the product delivered hereunder. MiLAN Technology will in
no case cover damages arising out of the product being used in a negligent fashion or manner.
Trademarks
© 2000 MiLAN, the MiLAN logo, and MiLAN Technology are either trademarks or registered trademarks of Digi International, Inc. in the United States and/or other countries. All other trademarks are the property of their respective holders.
To Contact MiLAN Technology
For prompt response when calling for service information, have the following information ready: Product serial number and rev; date of purchase; vendor or place of purchase.
You can reach MiLAN Technology technical support at: support@milan.com
Telephone: +1.408.744.2751 | Fax: +1.408.744.2771 | ||
MiLAN Technology 1299 Orleans Drive, Sunnyvale, CA | |||
Telephone: +1.408.744.2775 | Fax: +1.408.744.2793 | ||
http://www.milan.com | info@milan.com |
| |
© Copyright 2000 MiLAN Technology | Printed in the U.S.A. |
Coax to
Media Converter
Installation Guide
500 mA
MIL-C1111
|
| Ethernet |
|
|
| COAX to | |||
| IEEE 802.3 Compliant | |||
|
| POWER |
|
|
| COAX ACTIVE | TX ACTIVE | ||
| COAX ENABLE | TX LINK | ||
|
|
|
|
|
Coax |
|
|
|
|
|
| UTP | ||
|
|
|
|
|
Installation
Follow the steps given below to install the
1.Attach a UTP cable from network to
2.Attach a
3.Plug the power adapter into an AC outlet and connect the power
adapter cord to the unit.
EMI Note: Use shielded UTP (CAT 5) cabling for CISPR 22 classB.
Configuration-Termination Switch
Next to the coax cable connector, there are DIP switches that control the 50 Ohm internal resistor. Both switches are shipped in the “up” position (default, no termination).
Configuration Options
1.If the
•Setting switch 1 “up”
•Setting switch 2 “down”.
2.If the
length:
•Set both switches in the “down” position.
Note: For this configuration, you do not need a 50 Ohm terminator on the coax segment of the
©Copyright 2000 MiLAN Technology PN 90000213 Printed in the USA
LEDs
•TP ACT: Amber, indicates a packet activity on the
•COAX ACT: Amber, indicates a packet activity on the 10BASE2 network.
•TP LINK: Green, there is a good link on the
•COAX ENAB: Green, coax connection is established.
Cabling Options: MDI-X/MDI Switch
The
Cables used when the switch is in the MDI-X position:
•For a hub or repeater, use a swap cable (pins are connected 1 to 3, 2 to 6, 3 to 1, 6 to 2).
•For a workstation or PC, use a
Cables used when the switch is in the MDI position:
•For a hub or repeater, use a
•For a workstation or PC, use a swap cable (pins are connected 1 to 3, 2 to 6, 3 to 1, 6 to 2.
RJ-45 Specifications
1 2 3 4 5 6 7 8 | MDI | |||||||
Pin 1=RX+ |
|
|
|
|
|
|
| Pin 1=TX+ |
Pin 2=RX- |
|
|
|
|
|
|
| Pin 2=TX- |
|
|
|
|
|
|
| Pin 3=RX+ | |
Pin 3=TX+ |
|
|
|
|
|
|
| |
|
|
|
|
|
|
| Pin 6=RX- | |
Pin 6=TX- |
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|