Milan Technology MIL-S341X warranty 100m of CAT 5 UTP

To maximize the fiber cable distance, use one meter of CAT 5 UTP cable when connecting directly to a node (subject to fiber budget of 16dBm and collision domain restrictions). In full-duplex environments, use up to

100m of CAT 5 UTP and:

42Km of multi-mode optical fiber for MIL-S3412, S3413, S3414

415Km of single-mode optical fiber for MIL-S3413-15, S3414-15

440Km of single-mode optical fiber for MIL-S3413-40

470Km of single-mode optical fiber for MIL-S3413-70

4100Km of single-mode optical fiber for MIL-S3413-100

Multi-mode fiber (2Km)		Single-mode fiber (15Km)
4	1300nm wavelength	4	1300nm wavelength
4	62.5/125 micron diameter	4	9/125 micron diameter
4 Launch power: -19dBm minimum		4 Launch power: -15dBm
4	-31dBm receive sensitivity	4	-31dBm receive sensitivity
Single-mode fiber (40Km)		Single-mode fiber (60Km)
4	1300nm wavelength	4	1550nm wavelength
4	9/125 micron diameter	4	9/125 micron diameter
4 Launch power: -4dBm minimum		4 Launch power: 0dBm minimum
4	-34dBm receive sensitivity	4	-37dBm receive sensitivity

Single-mode fiber (100Km)

41550nm wavelength

49/125 micron diameter

4Launch power: 1.8dBm minimum

4-37dBm receive sensitivity

M DI-X / M DI S w itch (Fig ur e 1 )

The MDI-X/MDI switch allows for quick configuration of the 100BASE-TX port. Cables used when the switch is in the MDI-X position (the "left" position:

4For a hub/repeater, use a swap cable (pins are connected 1 to 3, 2 to 6, 3 to 1, and 6 to 2).

4For a workstation/PC, use a straight-through cable (pins are connected 1 to 1, 2 to 2, 3 to 3, and 6 to 6).

Cables used when the switch is in the MDI position (the"right" position):

4For a hub/repeater, use a straight-through cable (pins are connected 1 to 1, 2 to 2, 3 to 3, and 6 to 6).

4For a workstation/PC, use a swap cable (pins are connected 1 to 3, 2 to 6, 3 to 1, and 6 to 2).

MDI-X	1 2	3	4	5 6 7 8	MDI
p‹“@Q]rxK			@@@@@@@@@@@@@@@@@@@p‹“@Q]txK
p‹“@R]rxM					p‹“@R]txM
p‹“@S]txK					p‹“@S]rxK
p‹“@V]txM					p‹“@V]rxM

Ins ta lla tio n

1.Make any configuration changes to the module DIP switch settings.

2.Remove cover plate from MCS chassis.

3.Slide module into a slot through the card guides.

4.Firmly seat module into card-edge connector.

5.Secure module with thumbscrews located on module faceplate.

6.Plug in network connections.

Note: There is no need to power off the Media Conversion System.

Dia g no s tic LEDs a nd Co nd itio ns Ind ica ted

There are four LEDs for both UTP and fiber ports:

4D = Duplex; On indicates Full Duplex.

4A = Activity; On indicates receiving packets at port.

4S = Speed; On indicates rate is 100 Mbs.

4L = LINK; On indicates an active connection at port.

1

2

3

4

5

6

7

7- pin DIP Switch
MDI-X/MDI	MDI-X/MDI
Switch	Switch
LEDs
RJ -45	RJ -45
Connector	Connector
Fig ur e 2 . Ins id e	o f the M IL-S 3 4 1 0

Dip S w itch Fea tur es (Fig ur e 2 )

Speed and Half/Full Duplex or Auto Negotiation may be manually selected using the seven-position DIP switch.

All switches must be in the up position to utilize SNMP feature selection. Fiber ports operate at 100Mbs only.

Port 1 is on the left. Port 2 is on the right.

	Switch 1	Switch 2	Switch 3
	Auto-Negotiation Auto-Negotiation		Speed
Up Position	Enable Port 1	Enable Port 2	100Mbs Port 1
Down Position	Disable Port 1	Disable Port 2	10Mbs Port 1
	Switch 4	Switch 5	Switch 6	Switch 7
	Speed	Duplex	Duplex	Packet size
Up Position	100Mbs Port 2	FDX Port 1	FDX Port 2	1518 Bytes
Down Position	10Mbs Port 2	HDX Port 1	HDX Port 2	1522 Bytes

f‹‰š—‡@QN@rjMTU@p‹“”š™˜