3.2 Rear Panel
12 | 12 | 9 |
MODEL
SERIAL
POWER OUTPUTS
CH1
1+ | 1- |
POS | NEG |
BREAKER
|
|
|
|
|
|
|
|
|
| CH2 | CH1 | |
|
|
|
|
|
|
|
|
|
| 2+ | 2- | |
|
|
|
|
|
|
|
|
|
|
| ||
INPUT |
| INPUT |
|
|
| INPUT |
| INPUT | POS | NEG |
| |
|
|
|
|
| BRIDGE |
| ||||||
|
|
|
|
|
|
|
|
|
|
| ||
|
| TIP/PIN 2 |
|
|
|
| TIP/PIN 2 |
|
| 1+ | 2+ |
|
|
|
|
|
|
|
|
| POS | NEG |
| ||
|
| RING/PIN 3 | CH2 | CH1 | RING/PIN 3 |
|
|
| ||||
|
| SLEEVE/PIN 1 | SLEEVE/PIN 1 |
|
|
| OUTPUT1 | BRIDGE | ||||
|
|
|
|
|
|
|
|
|
| MONO | ||
|
|
|
|
|
|
|
|
|
| CH2 |
| |
|
|
|
|
|
|
|
| 2 | 1 | 1+ | 1- |
|
2 | 1 |
| NEW | TIDE | NEW | TIDE |
| POS | NEG |
| ||
3 |
|
|
|
|
|
|
|
|
|
| ||
|
| 3 |
| 3 |
|
|
| 3 |
|
| CH2 | |
|
|
| 2 | 1 | 2 | 1 |
|
|
|
| ||
|
| MODE |
|
|
|
| LIMITER |
|
|
|
|
|
PARALLEL | STEREO | BALANCED | BALANCED | OFF | PARALLEL |
|
|
| ||||
OUTPUT | BRIDGE | INPUT | INPUT | ON | OUTPUT |
| OUTPUT2 |
| ||||
|
|
|
| |||||||||
|
| 14 |
| 12 |
|
| 11 |
|
|
| 10 | 8 |
13
8Power Cord
You can connect the plug of power cord to the mains. Please make sure the voltage accepted by the unit . This
.is IEC power cord.
9Manual Reset Pushing-Button
This switch works as fuse for protecting the unit from damage. When the unit is overloaded or the temperature inside the unit is too high, this
10Output Connector
These connectors have two kinds: Binding post and Neutrik connector. You can choose proper connectors according to practical need. For your safety, please be careful when do connecting work.
11Limter Switch
Set this switch at "ON" position, once the output level is above maximum output level, the clip begin, thus keeping consistent output level for protecting apparatus. If the switch is set at "OFF", this clip function doesn't work.
12Balanced Input Connector
These connectors connect the input signal of channel1 and channel 2 separately.
13Balanced Output Connector
These two output connectors are paralleled inside with input connectors. It enables the unit work under paralleled mode. Please also refer to wiring diagram for paralleled mode.
14Mode Selector
Total two optional modes: Up for Stereo mode; Down for Bridge mode.
-Stereo
In this mode, Channel 1 and Channel 2 operate independently ( just as traditional stereo amplifier). The signal input into channel 1 can be output from channel 1 only, similarly, the signal input into channel 2 can be output from channel 2 only.
You can also operate the paralleled mode via outside wiring, so, the signal input from channel 1 or 2 will be output from both channel 1 and 2 simultaneously. Details refer to the chapter 4.
-Bridge
In this mode, the signal input into channel 1 will be output from the bridged end, on other hand, the output level control of channel 2 should be turn down to smallest.
6