Mitsubishi Electronics SL4U, XL8U, XL4U, Sl4U When sRGB is ON, only the main data are effective

ITEM	ASCII	HEX				VALUE
CLAMP POSITION	CLP	43h	4Ch	50h		00 - 63
CLAMP WIDTH	CLW	43h	4Ch	57h		01 - 63
VERT. SYNC.	VSC	56h	53h	43h		0 (AUTO), 1 (OFF)
SHUTTER (U)	SHU	53h	48h	55h		00 - 20
SHUTTER (L)	SHL	53h	48h	4Ch		00 - 20
SHUTTER (LS)	SHLS	53h	48h	4Ch	53h	00 - 20
SHUTTER (RS)	SHRS	53h	48h	52h	53h	00 - 20

*1) When sRGB is ON, only the main data are effective.

•Some commands are not executed depending on the input signal. The operational restrictions same as those on the menu setting are applied. Refer to “Menu operation” in the User Manual for more details.

How to set the grade

Use the ASCII codes to set the grade for setting data. Please refer to the table below for the HEX code.

ASCII

'+'

'–'

'0'

'1'

'2'

'3'

'4'

'5'

'6'

'7'

'8'

'9'

HEX

2Bh

2Dh

30h

31h

32h

33h

34h

35h

36h

37h

38h

39h

[Example 1] When setting the AUTO POWER ON to ON. (Figures and symbols enclosed in quotation marks are ASCII codes.):

Sending commands	Status code from	Description
from the PC, etc.	the projector
30 30 41 50 4F 4E 31 0D		Command for setting the
'0' '0' 'A' 'P' 'O' 'N' '1' ' '		AUTO POWER ON to ON
	30 30 41 50 4F 4E 31 0D	Command receipt confirmation
	'0' '0' 'A' 'P' 'O' 'N' '1' ' '	(Command echo back)

The data code of CONTRAST and BRIGHTNESS consists of the difference data between R and G, the main data, and the difference data between B and G.

[Example 2] When setting the difference data between R and G to +10, the main data to 0, and the difference data between B and G to -5. (Figures and symbols enclosed in quotation marks are ASCII codes.):

Sending commands		Status code from	Description
from the PC, etc.		the projector
30 30 50 2B 31 30 2B 30 30 2D 30 35 0D			Command for setting the
'0' '0' 'P' '+' '1' '0' '+' '0' '0' '-' '0' '5' '	'		picture control
		30 30 50 2B 31 30 2B 30 30 2D 30 35 0D	Command receipt confirmation
		'0' '0' 'P' '+' '1' '0' '+' '0' '0' '-' '0' '5' ' '	(Command echo back)

[Example 3] When checking the TINT setting (when the TINT is set to +10). (Figures and symbols enclosed in quotation marks are ASCII codes.)::

Sending commands	Status code from	Description
from the PC, etc.	the projector
30 30 53 0D		Command for checking
'0' '0' 'S' ' '		the TINT setting
	30 30 53 2B 31 30 0D	Check result (+10)
	'0' '0' 'S' '+' '1' '0' ' '

•To set 0 in the menu setting commands (COLOR MATRIX, COLOR, TINT, SHARPNESS), enter +00. (-00 is invalid.)

5