43870rev1 b:43870 rev1 11/03/2009 15:47 Page 6
FEATURES
⁄Lid with lid release lever
¤Spout filter
‹Base and cable tidy
›360° connector
fiCord storage
flWater level indicator with illuminating light
‡Temperature gauge
·+ Temperature control button
‚- Temperature control button
„Start/Stop button
BEFORE FIRST
USE
Before using the appliance for the first time, fill with water, boil and pour away.
Water
Temperature
Getting the right water temperature is essential for you to enjoy your favourite hot drinks with maximum flavour and taste. Eg. if you’re a green tea drinker, water that is brewed too hot will scorch the leaves and create a bitter taste. If you’re a coffee lover, then getting the water temperature is crucial to getting the best flavours from the ground coffee.
See the table on the front of this booklet for a quick reference guide for some of the most popular hot drinks to allow you to get the most from your IntelliBoil Jug
• | Always ensure that the | • | It is not possible to reheat the | |
| appliance is filled until the |
| water in the kettle until it has | |
| water is visible through the |
| dropped below 80°C on the | |
| level indicator. |
| 85°C setting and 90°C on the | |
• | Boil only as much water as |
| 95°C. This prevents | |
| unnecessary | |||
| you need as this saves |
| energy usage. | |
| electricity. | • | It is not possible to use the | |
1 | Place the appliance on the | |||
| kettle to reduce the | |||
| base unit, ensuring the |
| temperature of previously | |
| appliance locates onto the |
| heated water. | |
| 360° connector. | • | On the 100oC setting it is | |
| The 360° connector allows | |||
• |
| possible to | ||
| the appliance to be located |
| as soon as the kettle has | |
| at any position - ideal for left |
| switched off. | |
| and right handed users and | • | When there is no function | |
| convenient positioning on | |||
| worktop. |
| activated for 15 minutes, the | |
2 | Plug in and switch on at the |
| LED display and the internal | |
| illumination will switch off. | |||
| wall socket. |
| The display will wake up if | |
3 | The gauge shows the |
| any button is pressed or if | |
| the kettle is lifted up and | |||
| temperature of the water, |
| replaced back on its base. | |
| if the current water |
|
| |
| temperature is below 40°C |
| Filter removal | |
| the display will read LO. |
| ||
4 | The kettle is automatically set | 1 | Open the lid. | |
| to heat the water to 100°C. To | 2 | Lift the filter upwards from its | |
| heat the water in the kettle to | |||
| 85°C or 95°C, use the + and |
| location using the tab | |
|
| provided. | ||
| adjust the selected heating | 3 | To refit the filter, slot it into | |
| temperature. | |||
|
|
| the side wall guides and | |
• | The red dot will highlight the |
| press down firmly. Ensure the | |
| user selected setting and the |
| filter is correctly located into | |
| selected temperature will |
| the central guide. | |
| flash on the digital gauge for |
| WARNING: Make sure that | |
| 3 seconds. |
| ||
|
|
| the filter is put in correctly | |
• | After the desired temperature |
| otherwise the lid will not | |
| is selected, the display will |
| close. | |
| return to showing the current |
|
| |
| water temperature. |
| Dry Boil | |
5 | Press the start/stop button to |
| ||
| The kettle cuts off and | |||
| begin heating the water. The |
| ||
| kettle will beep and show the |
| beeps when switched on | |
| selected temperature for 3 |
| while empty. | |
| seconds. |
|
|
Kettle.
OPERATING THE APPLIANCE
The integrated water level indicators allow you to easily see the amount of water in the kettle.
6When the required temperature has been reached, the kettle will beep 3 times and switch off.
•After the kettle has switched off, the display will show the current temperature of the water.
Remove the kettle from its base to stop the beeping and then fill with water for boiling.
| 4 | UK Helpline | 0844 871 0954 Replacement parts 0844 873 0719 Ireland 1800 409 119 | |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|