Morphy Richards NO NUMBER manual Anti-scale system, Electrical requirements, Instructions for use

Job: Ion 441375253 Rev 3 -- Color: Composite -- Signature 2, Sheet 1, Front -- Plate 3

No drip system

Your iron is fitted with a no drip system

which is designed to prevent water escaping from the soleplate when the iron is too cold.

During use, the no drip system may emit a loud click, particularly during heat-up or whilst cooling down. This is perfectly normal and indicates that the system is functioning correctly.

Anti-scale system

(certain models only)

The anti-scale cartridge is designed to reduce the build-up of limescale which occurs during steam ironing, this will prolong the working life of your iron. However, please note that the anti-scale cartridge will not completely stop the natural process of limescale build-up.

Using your anti-scale iron for the first time If you are using your iron for the first time

Replacement anti-scale refills

To obtain replacement anti-scale refills telephone our spares number

on: 0870 167 6646.

Filling / Refilling your anti-scale cartridge

1Empty any remaining water from the tank, (see

emptying and storing section).

2 Remove the anti-scale cartridge from the iron by turning it anti-clockwise quarter of a turn and pulling it out.

3	Remove the cartridge lid
	as follows, hold the
	cartridge upright and
	gently squeeze it by the
	retaining lugs. Gently pull
	off the lid. If you are
	refilling, dispose of the
	used sachet.
4	Remove the anti-scale

•WARNING: when not in use, your iron should never be placed flat and left on an ironing board.

•To prevent damage to the textile being ironed, follow the temperature guide carefully. (Test the inside of the hem of the garment).

•When ironing is complete, remove the plug from the socket, empty any remaining water from the tank, and allow to cool before storage.

•If you drop or severely knock your iron this could cause internal damage even if the outside appears alright. Have it checked by a qualified electrician.

•It is recommended that you use up one beaker of water by operating your iron’s steam and shot of steam functions before ironing any clothes as some dripping may occur while your irons steam system is activated.

Electrical requirements

Check that the voltage on the rating plate of your appliance corresponds with your house electricity supply which must be A.C. (Alternating current).

If the socket outlets in your home are not suitable for the plug supplied with this appliance the plug should be removed and the appropriate one fitted.

WARNING : The plug removed from the mains lead, if severed, must be destroyed as a plug with a bared flexible cord is hazardous if engaged into a live socket outlet.

Should the fuse in the 13 amp plug require changing a 13 amp BS1362 fuse must be fitted.

WARNING: THIS APPLIANCE MUST BE EARTHED.

you will notice that there is no anti-scale sachet present in the anti-scale cartridge. To keep the granules in optimum working condition they are stored in an air-tight container located in the packaging of your iron. To activate the anti-scale system you must place the anti-scale cartridge with sachet, as described below.

Refilling intervals

How often you need to refill your anti- scale cartridge depends on how often you use your iron with its steam functions and how ‘hard’ your water supply is. Water hardness varies greatly from one area to another. For advice on the relative hardness of your water, contact your local water supplier.

If, on average you spend 2 hours per week ironing, then we suggest you refill your anti-scale cartridge as shown in the table. If you iron more or less frequently then you should alter the interval between refills accordingly.

Water hardness	Soft	Medium	Hard
Refill interval	6	3	11/2
(months)

sachet from its packaging.

5Fit the new sachet into the cartridge.

6Replace the lid back on the cartridge by aligning

the holes with their lugs and pressing down until it clicks shut on both sides.

7Insert the cartridge back in its hole. Push it in as far as possible making sure it is aligned as shown. Turn it clockwise until the pointer aligns with the marker on

the iron and it is closed flush tight.

8Your iron is now ready to use and the water tank can be filled.

Instructions for use

Temperature guide

Heat setting markings on the adjustable control dial of all Morphy Richards irons match those of the International Textile Care Labelling Code.

Symbol
	(120˚C Max) Cool		(160˚C Max) Warm				(210˚C Max) Hot
Control knob	Do not iron
positions	at all
Fabric	Nylon, Acetates			Wool, Polyester			Cotton, Linen
	e.g. Acrilan			mixtures e.g.			Rayon, Rayon
	Courtelle, Orlon			Polyester/Cotton			mixtures,
	Triacetates, e.g.						e.g. Rayon/Linen
	Tricel/Polyester
Ironing	Iron on wrong side						Fabrics requiring this
	if moisture required						setting usually require
	use damp cloth						steam pressing for heavy
	(Not Acetate)						cotton, denim etc.
With water in tank		Dry and spray				Steam/spray/shot of steam
								Jet clean
Without water in tank					Dry ironing

6

3