3
4

TURNING HEADSET

ON/OFF

MAKING CALLS

To turn your headset on, press and hold
the Call button until the indicator light
flashes. Then, release the button.
To turn your headset off, press and hold
the Call button until the indicator light
flashes rapidly and then turns off.

INDICATOR LIGHTS

IMPORTANT:

Be sure to first follow the

Quick Start Guide

on the reverse side

of this guide

to complete initial setup

of your H3.

WEARING THE

HEADSET

Open the earhook.
Loop the earhook over your ear.
Press the headset to your ear.
1
2
3

AUDIO TONES

The audio tones provide information about your
headset status.
Audio Tone Headset Status
Single high tone when Volume at minimum
pressing volume button or maximum
Five rapid high tones Low battery
repeated every 60 sec.
No audio indications; Out of range
deteriorating quality
Ring tone Incoming call
Single high tone Pairing confirmation
Single low tone Voice activation
Dual high/low tone Voice tag not
   recognized
Single high tone End call
Low to high tone  Phone network 
not available
Two ascending tones Mute enabled
Two descending tones Mute disabled
Call
Button
Note: Your H3 supports both Handsfree and Headset
Profiles. Accessing call functions depends upon which
profile your phone supports. See your phone's user's guide
for more information.
Function  Action
Make a voice dial call Tap the Call button
and speak the 
name after the tone
End a call Tap the Call button
Receive a call Tap the Call button
Reject a call Press and hold the
Call button until you
hear a beep
Redial last call Press and hold the
Call button until you
hear a beep
Answer a second Press and hold the
incoming call Call button (places
first call on hold)
MAKING CALLS CONTINUED

Function  Action
Toggle between two Press and hold
active calls the Call button
Join a 3-way call Press and hold
both Volume buttons
Put an active call on Press and hold the
hold or resume a call Call button until you
on hold  hear a beep
Transfer a call from the Tap the Call button
phone to the headset
Disable or enable the Press and hold
indicator light both Volume
buttons for 3 to 4
   seconds
Mute or unmute a call Tap both Volume
   buttons
Note: Some features are phone/network dependent.
The indicator light provides information about
your headset status.
With the Charger Plugged In
Headset Indicator Headset Status
On (steady) Charging
Off Charging complete
With No Charger Plugged In
Headset Indicator Headset Status
Off Power off
On (steady) Pairing mode
10 rapid flashes Pairing successful
Slow pulse  Connected
(on a call)
Quick flash Standby
(not on call)
Note: After 5 minutes of inactivity, the light stops flashing to
conserve power, but the headset remains in standby mode.
Features and Functions Guide
H3
Bluetooth®
Handsfree Headset

CHANGING FOR USE

ON OTHER EAR

Open the earhook 90
degrees from the
headset.
Gently lift and pull the
top of the earhook up
and off the upper
hinge pin. Then, pull it
away to remove it.
Flip the headset over.
Hook the bottom of
the earhook onto the
lower hinge pin, then
lift and pull the top of
the earhook over the
upper hinge pin.
1
2
3
4
You can wear your H3 headset on your left or
right ear. The headset comes ready for the right
ear. To change the headset for the left ear:

CHANGING VOLUME

BUTTON ORIENTATION

If you change your headset to wear on the
other ear, you can also change the
orientation of the volume buttons.
Turn the headset power off.
Press the Call button along with the
Volume button you want to assign as
"volume up" button until the indicator
light flashes twice.
The headset power turns on.
1
2
2 Pull Earhook Up
Hinge Pin
1 Open Earhook
Volume
Buttons
Call
Button