IMPORTANT:

Be sure to first follow the

Quick Start Guide

on the reverse side to

complete initial setup of

your H700.

IMPORTANT:

Be sure to first follow the

Quick Start Guide

on the reverse side to

complete initial setup of

your H700.

H700

Bluetooth®

Handsfree Headset

TURNING ON AND OFF
To turn your headset on, open the
headset boom. The indicator light flashes
blue if paired with another device, or is
steadily lit in purple if ready to be paired.
To turn your headset off, close the
headset boom. The indicator light will turn
off.
To conserve battery power, turn off your
headset when you don't plan to use it for
WEARING THE HEADSET
Open the headset boom, then open the
earhook (45 from the headset).
Loop the earhook over your ear.
Press the headset to your ear.
Point the headset boom towards your
mouth.
1
2
3
4
CHANGING VOLUME BUTTON ORIENTATION
You can also change the orientation of the
volume buttons on your headset.
Turn the headset power off by closing
the headset boom.
Press the Call E button until the
indicator light becomes steadily lit in
purple, then press the Volume button
you want to assign as the "volume up"
button.
1
2
MAKING CALLS
Note: Your H700 supports both Handsfree and Headset
Profiles. Accessing call functions depends upon which
profile your phone supports. See your phone's user's guide
for more information.
FunctionAction
Make a voice dial callTap the Call button
and speak the
name after the tone
End a callTap the Call button
Receive a callOpen headset boom
or tap the Call button
(if boom is already
open)
Reject a callPress and hold the
Call button until you
hear a beep
Redial last callPress and hold the
Call button until you
hear a beep
MAKING CALLS CONTINUED
FunctionAction
Answer a secondPress and hold the
incoming callCall button (places
first call on hold)
Toggle between twoPress and hold
active callsthe Call button
Join a 3-way callPress and hold
both Volume buttons
Put an active call onPress and hold the
hold or resume a callCall button until you
on holdhear a beep
Transfer a call from theOpen headset boom
phone to the headset
Disable thePress and hold
indicator lightboth Volume
buttons for 3 to 4
seconds
Mute or unmute a callTap both Volume
buttons
Note: Some features are phone/network dependent.
INDICATOR LIGHTS
With the Charger Plugged In
Indicator LightHeadset Status
Red (steady)Charging (less than
80% charged)
Yellow (steady)Charging (more than
80% charged)
Green (steady) Charging complete
With No Charger Plugged In
Indicator Light Headset Status
Off Power off
Purple (steady) Pairing mode/
Volume button
orientation
Red Battery low
Blue (10 rapid flashes) Pairing successful
Blue (slow pulse) Connected (on a call)
Blue (quick flash) St andby (not on call)
Note: After 5 minutes of inactivity, the light stops flashing to
conserve power, but the headset remains in standby mode.
AUDIO TONES
The audio tones provide information about your
headset status.
Audio ToneHeadset Status
Single high tone whenVolume at minimum
pressing Volume buttonor maximum
Five rapid high tonesLow battery
repeated every 60 sec.
No audio indications;Out of range
deteriorating quality
Ring toneIncoming call
Single high tonePairing confirmation
Single low toneVoice activation
Dual high/low toneVoice tag not
recognized
Single high toneEnd call
Low to high tonePhone network
not available
Two ascending tonesMute enabled
Two descending tonesMute disabled
CHANGING FOR USEON OTHER EAR
Open the headset boom,
then open the earhook
(90 from the headset).
Gently lift and pull the
top of the earhook up
and off the upper hinge
pin. Then, pull it away to
remove it.
Flip the headset over.
Hook the bottom of the
earhook onto the lower
hinge pin, then lift and
pull the top of the
earhook over the upper
hinge pin.
1
2
3
4
You can wear your H700 headset on your left or
right ear. The headset comes ready for the right
ear. To change the headset for the left ear:
1 Open Earhook
2 Pull Earhook Up
Hinge Pin
Multi-Color
Indicator Light
Volume
Buttons
Call
Button