
Operating Instructions for
Motorola
Advanced Series
MXv3 Remote Control
(888)
Operating Instructions for
Motorola
Advanced Series
MXv3 Remote Control
Battery Installation
Install two AA alkaline batteries, as shown.
1.On the back of the remote, push down on the tab and lift the cover off.
2.Match the batteries to the + and - marks inside the battery case, then insert two AA alkaline batteries.
3.Press the battery cover back into place.
Programming the Remote to Control Other Devices
The remote control will only control the device that is selected by the appropriate mode key (STB, TV, DVD and AUX). The mode key light for the selected device flashes each time a valid key is pressed. In order to control other devices with your MXv3 Remote Control, you need to tell the remote control what types of devices you have. Sections A and B take you through the steps needed to do this. The volume controls will control your
To use your MXv3 Remote Control for your other devices, you will need to set up the TV, DVD and AUX mode keys to control the devices (Section A).
Please refer to the code list for a list of supported brands and models. If you do not find the brand of your device on the supported code list, please refer to section B for the search function or you may use section C for instructions on the learning feature of your remote control.
If you have an integrated or combo unit such as a TV/DVD, each component of the unit may need to be set up separately by setting up both the TV and DVD mode keys.
Note: The DVD and AUX mode keys can be set up with any code. The TV mode key can only be set up with TV codes.
Note: Learning cannot be performed for any mode until after that mode is set up with a valid code. So, to learn the keys, first set up the mode with a valid code, see section A, (select any code for the appropriate mode from the code list), then follow the steps below.
C-I. Learning Commands
1.Press and hold the mode key (TV, DVD or AUX) on the MXv3 remote and, while holding it pressed, press the LEARN key for 1 second, then release both keys.
Original Remote and Motorola Remote
1 inch apart
2.All of the mode keys will flash and then the selected mode key light remains on.
3.On your MXv3 Remote, press and release the key that you want to teach.
4.While pointing your original remote at the bottom of your MXv3 Remote, approximately 1 inch apart, press and hold the original remote key until the mode key light blinks once and stays on. (If there is a learning problem, the mode key light blinks for 3 seconds and stays on. If this happens, repeat steps 3 and 4 above.)
5.Repeat steps 3 and 4 on previous page for each key you want your MXv3 Remote Control to learn.
6.Press and release the LEARN key when all desired remote commands have been learned.
If you have encountered difficulties with the
LEARN key setup, please refer to Section K: Troubleshooting Learning.
Note: It is not necessary to have your MXv3 Remote Control learn every key from your original remote, since most of the keys will not be used under normal daily use. The best practice is to teach only the keys that help you navigate for the best experience, like your volume up and down.
D. Clearing Commands
D-I. To Clear all Learned Commands (under a single mode)
1. Press and hold the mode key (TV, DVD or |
AUX) and, while holding it pressed, press the |
LEARN key for one second, then release both |
keys. |
2. All the mode keys will flash and the selected |
E-II. Volume Control Depends on Device Selected
1.Press and hold the TV key and, while holding it pressed, press the OK key for 1 second.
2.Release both keys. All of the mode keys will flash, followed by the TV mode key light remaining on.
3.Press and hold the MUTE key for 3 seconds until the TV mode key light briefly turns off, then stays on, then release the MUTE key.
4.Press and release the MUTE key to save the setting. The TV mode key light turns off, indicating successful setup. The volume commands will now work for different devices.
Note: If a programmed mode key has no volume commands of its own, then the volume control will normally operate the TV. If an invalid key is pressed, the selected mode key light flashes for 3 seconds and turns off. The remote control returns to normal operation and you will need to start over.
If no key is pressed within 30 seconds, the remote control times out, the selected mode key light flashes for 3 seconds and turns off. The remote control returns to normal operation, at which time you can start over.
F. Channel Control Setup Options
The channel controls (Channel Up/Down,
F-I. Channel Control Depends on Device Selected
1.Press and hold the TV key and, while holding it pressed, press the OK key for 1 second.
2.Release both keys and all of the mode keys flash, followed by the TV mode key light remaining on.
3.Press and hold the LAST key for 3 seconds until the TV mode key light briefly turns off, then stays on, then release the LAST key.
4.Press and release the LAST key to save the setting. The TV mode key light turns off, indicating successful setup. The channel commands will now work for different devices.
To remove a mode from the Power key:
1.Press and hold the STB key and, while holding it pressed, press the OK key for 1 second. Then release both keys. You are now in setup mode.
2.Press and release the mode key (TV, DVD or AUX) you want to disable.
3.Press and release the 0 key. The selected mode is now disabled. If no mode key is pressed in step 2, ALL modes (TV, DVD and AUX) will be disabled.
Note: You can turn individual devices on/off by pressing the desired mode key, followed by the Power key. It is important to point your MXv3 Remote directly toward the devices for this feature to operate correctly.
I. Backlight Cancellation Feature
Your MXv3 Remote Control has the ability to toggle between turning the backlights on or off. If you wish to use this feature, follow these instructions:
1.Press and hold the TV key and, while holding it pressed, press the OK key for 1 second and release both keys at the same time.
2.All the mode keys flash and the TV mode key light stays on.
3.Press the GUIDE key and all backlights will no longer turn on. To reverse this process so that the backlights turn on when the remote control is being used, simply follow the same steps of the above section one more time.
J. Resetting the Remote Control to the Factory Default Settings
1. Press and hold the TV key and, while holding |
it pressed, press the OK key for 1 second and |
release both keys at the same time. |
2. All the mode keys will flash and the TV mode |
key light will stay on. |
3. Press and hold the DELETE key for 3 seconds |
until the TV mode key blinks and stays off. The |
remote control is now reset to factory default |
settings. If you want to use the remote control for |
your TV and other devices, you will need to set |
up the TV, DVD and AUX mode keys. |
4. If no key is pressed within 30 seconds, the |
remote control times out. The selected mode |
key light flashes for 3 seconds and turns off. The |
remote control returns to normal operation and |
3/11
BUTTON FUNCTIONS
Record
Controls Record functions (only available on Digital Video Recorder
menu
Displays the Applications Menu
replay
Replays the previous few seconds of a program
On demand
Provides direct access to on Demand Channel
FWD
Forward ahead to stored or recorded programs
STB, TV, DVD, AUX
Used to select the component you want
to operate and signals remote control actively
VCR/dvd/mod keys 7,8,4,;
Perform standard VCR and DVD functions when in DVD or VCR mode, and DVR or
power
Allows you to turn your TV, VCR, DVD,
AUX and
Tv/video
Selects the video source from available video components
recorded tv
Displays the Digital Video Recorder (DVR) menu
Learn
Displays information about the program currently playing or highlighted in
the program guide
Interactive
Available for future use
A. Manual Programming
How to set up the TV, DVD or AUX mode keys:
1.Power on the device you want to program and locate the
2.Press and hold the mode key (TV, DVD or AUX) and, while holding it pressed, press the OK key for 1 second.
3.Release both keys. All of the mode keys will flash, then the selected mode key light will stay lit.
4. Enter the
5.Point the remote control at the selected device and press the power key once. The device should turn off. If the device stayed on, repeat steps 2 through 5, trying each code for your brand until you find the correct code
Repeat the steps on the previous page to set up another device. To use the remote control for your
Note: If an invalid code is entered or no key is
mode key light will stay on. |
3. Press and release the LEARN key once. The |
mode key light blinks off. |
4. Press and release the DELETE key. The mode |
key light turns off. All learned commands under |
that mode are now cleared. |
D-II. To Clear all Learned Commands (under ALL modes)
1.Press and hold the mode key (TV, DVD or AUX) and, while holding it pressed, press the LEARN key for 1 second, then release both keys.
2.All the mode keys will flash and the selected mode key light will stay on.
3.Press and release the LEARN key twice. The mode key light blinks off.
4.Press and release the DELETE key. The mode key light turns off. All learned commands under that mode are now cleared.
E. Volume Control Setup Options
The volume controls will control your
1.Press and hold the TV key and, while holding it pressed, press the OK key for 1 second.
2.Release both keys and all of the mode keys will flash, followed by the TV mode key light remaining on.
3.Press and hold the LAST key for 3 seconds until the TV mode key light briefly turns off, then remains on.
4.Press and release the STB mode key. The selected mode key light remains on.
5.Press and release the LAST key to save the setting.
The STB mode key light will turn off, indicating a successful initial setup. The channel commands will be set up for your
G. Mode Deactivation
If you’d like to deactivate a device mode, then follow the instructions below:
you will need to start over. |
K. Troubleshooting Learning
You can only learn one device type under any one mode key. For example, only learn TV codes under the TV mode, DVD codes under the DVD mode, etc. If you are trying to learn from a “Universal” remote, it might have more than one code type stored under a mode.
a. No functions may be stored under the LEARN key, or in the STB mode.
b. Depending on the remote you are trying to learn, some keys may not be learnable.
c. Only one original device type can be learned per individual mode.
d. Use fresh batteries for your original remote and your MXv3 Remote Control.
e. Stay at least 3 feet away from incandescent or
f. Before learning, clear all learned commands (refer to Section
g. Point your original remote at the bottom end of
back
Return to previous menu screen or TV channel
cursor navigation pad 5,6,4,3
Navigates to and highlights an item from
exit
Use to exit setup screens
Volume + or -
Raises or lowers the sound level
guide
Displays the Program
Guide Listings
Mute
Silences the audio. Press to activate.
Press again to restore to original level
delete
Edit text on the screen
Thank you for choosing FTC Vision. For user support, or to report trouble, please call 611 from any FTC, FTC Diversified or FTC Wireless phone. For Vision tutorials, please visit our website at
ok/sELECT
Selects highlighted screen options
INFO
Displays information about the program currently playing or highlighted in the program guide
a
Allows you to select available aspect ratios through the STB
Provides direct access to favorites channel
C
Available for future use
ch/pg + or -
Navigate to and highlight an item from the
last
Returns to the previous channel
number pad
Enter numbers to tune to channels. Also, make numeric entries on
Note: You can also use 5/6or the program guide as alternate ways to tune channels.
ZOOM
Allows access to viewing options, including aspect ratios, audio languages and subtitles
pressed at all for 30 seconds, the mode key light flashes for 3 seconds and turns off. The remote control returns to normal operation and you will need to start over from step A2 to set up the device.
B. Using the Search Function
To search for a particular device code for DVD or AUX, e.g., VCR, use the Manual Programming for section A and program DVD or AUX with any VCR code prior to starting a search.
1.Turn on the device you want to control and point the remote at that device.
2.Press and hold the mode key (TV, DVD or AUX) and, while holding it pressed, press the OK key for 1 second.
3.Release both keys. All of the mode keys will flash then the selected mode key light will stay lit.
4.Press the power button repetitively until the selected device turns off. Once your device has turned off, press OK to save the code.
5.To indicate a successful setup, the selected mode key will turn off and you are ready to set up another device by following steps 1 thru 4 of this section.
C. Learning
if DVD mode is selected, then volume controls your STB. If TV mode is programmed and DVD mode is selected, then volume controls your TV. If you’d like the volume commands to operate from just one device, e.g., always TV, then follow the instructions in Section
E-I. Volume Always Controls the Same Device
1.Press the TV key and, while holding it pressed, press the OK key for 1 second.
2.Release both keys and all of the mode keys will flash, followed by the TV mode key light remaining on.
3.Press and hold the MUTE key for 3 seconds until the TV mode key light briefly turns off, then remains on. Press and release the mode key that you always want to operate the volume commands (STB, TV, DVD or AUX). The selected mode key light will remain on.
4.Press and release the MUTE key to save the setting. The selected mode key light will turn off, indicating a successful setup. The volume commands will be set up for the selected device, despite what mode is selected.
If the selected mode key light flashes for 3 seconds and turns off, then the selected mode
1.Press and hold the mode key to be deactivated (TV, DVD or AUX) and, while holding it pressed, press the OK key for 1 second.
2.Release both keys, all of the mode keys will flash and then the selected mode key light will remain on.
3.Enter the
H. Multiple Device Power
Control Setup Options
After pressing the STB key, pressing the Power key turns the
1. Press and hold the STB key and, while holding |
it pressed, press the OK key for 1 second. Then |
release both keys. You are now in setup mode. |
2. Press and release the mode key (TV, DVD or |
AUX) you want to enable. |
3. Press and release the 1 key. The selected |
mode is now enabled. If no mode key is pressed |
your MXv3 Remote Control so the IR elements on both remotes are directly in line with each other (see diagram in
h. Avoid learning your original remote’s Volume/ Mute keys unless you are sure these operate the same device.
i. Avoid learning your original remote’s VCR or DVD transport keys unless you’re sure these operate the same device.
j. If learning the first or second keys for a mode results in continuous errors, then try the following:
i.End the learn session by pressing the LEARN key.
ii. Clear out the learned commands for |
that mode. |
iii. Check that the IR elements are correctly |
aligned between the two remotes. |
iv. Adjust the distance between the two remotes |
to be closer (e.g., half an inch) or farther away |
(e.g., 2 inches) from each other. |
v. Try learning the original remote for that |
mode again. If problems reoccur with the |
same key, check the original remote key |
being learned. Does it transmit? Does it |
operate the target device? Try learning that |
key under a different clear mode. If it learns |
OK, then it is likely to be a different code |
BUTTONS SHOULD BE PRESSED AND RELEASED QUICKLY, AS HOLDING BUTTONS MAY EXECUTE ADDITIONAL COMMANDS.
If the code for your device is not found in the code list and the search feature was not able to find the code for your device, then the learning feature may be your best option. The learning feature lets you “learn” functions from your original remote control.
will have no volume commands of its own and you will need to start over from step 1 above and select a different mode to program the device.
in step 2, ALL modes (TV, DVD and AUX) will |
be enabled. |
type from the others and cannot be learned |
under the same mode. |