Mr. Heater MH45T Assembly Procedure, Lighting Instructions, Ventilation, Minimum Clearance From

Models: MH45T

1 16
Download 16 pages 53.36 Kb
Page 5
Image 5
5. ASSEMBLY PROCEDURE

E.

CONNECTING HEATER TO PROPANE CYLINDER: Always

5. ASSEMBLY PROCEDURE

 

connect the heater to the bulk cylinder in the outdoors or in a

A.

Make sure the regulator knob on the heater is “off” by turning

 

well ventilated area. NEVER connect this heater to a cylinder near

 

an open flame.

 

knob clockwise to the “OFF” position.

F.

USE OF HEATER: Always operate the heater with the propane

B.

Carefully screw POL nut directly into bulk propane cylinder,

 

cylinder in an upright position on a level noncombustible surface.

 

counterclockwise. REMEMBER – This is a left hand thread – see

 

NEVER place the cylinder on its side when operating the heater.

 

Figure 1. Make sure the heater is in a vertical upright position

G.

ATTEND HEATER: Do not leave heater unattended while it is in

 

and directed away from the collar of the bulk tank. Use the hand

 

wheel to tighten the POL fitting – left hand thread – see Fig. 1.

 

operation.

 

 

 

 

H.

ALWAYS USE A MATCH TO LIGHT HEATER: NEVER attempt to

6. LIGHTING INSTRUCTIONS

 

light the heater with a spark lighter.

A.

Before attempting to light the heater, check all fittings and

I.

DO NOT TAMPER: Should the heater not perform properly,

 

connections with a soap solution. NEVER USE A MATCH TO

 

such as little or no heat when operating in the “Hi” position, or

 

CHECK FOR LEAKS. Should a gas leak occur, do not attempt

 

for any other reason, DO NOT ATTEMPT TO REPAIR OR TAMPER

 

to repair or use heater. Return the heater to your dealer or the

 

with the heater. Any tampering could make the use of the heater

 

address given on back page.

 

unsafe and dangerous. Return the heater to the dealer or the

B.

Fuel – This heater must be used only with a vapor withdrawal LP

 

address given on last page for repair or replacement.

 

 

gas bulk cylinder. THE BULK TANK MUST BE EQUIPPED WITH A

J.

FOR STORAGE: The heater Hi-Med-Lo-Off regulating valve

 

 

STANDARD POL VALVE.

 

should always be turned to “Off” when the heater is not in

 

 

 

use. Allow at least 15 minutes for cooling before handling and

 

WARNING:

 

storing. Detach propane cylinder from heater before storing. DO

 

USE HD.5 PROPANE GAS ONLY. DO NOT USE ANY OTHER

 

NOT store propane cylinders near open flame or heat.

 

 

 

TYPE FUEL. SEE YOUR PROPANE DEALER IF YOU HAVE ANY

K.

DO NOT TRANSPORT OR MOVE APPLIANCE WHILE IN

 

 

QUESTIONS REGARDING FUEL.

 

OPERATION OR WHILE HEATER IS ATTACHED. FOLLOW

 

 

 

C.

Turn the heater’s “Hi-Med-Lo-Off” regulator knob to “Med”

 

SHUTDOWN AND STORAGE INSTRUCTIONS TO TRANSPORT

 

 

(counterclockwise).

 

OR MOVE THIS APPLIANCE.

 

 

 

 

3. VENTILATION

D.

To light a burner, MH45T Model, place a lit match across the

 

mesh screen where you see “light here” on reflector. (See Fig.

A. WARNING: This heater is an unvented appliance and

 

4) THEN push in valve button on Safety Shutoff Valve. After the

 

burner is lit, continue to hold valve button in for 30 seconds,

 

MUST be used ONLY in a well ventilated area. NEVER

 

 

 

then release the button slowly. CAUTION: DO NOT PUSH IN

 

attempt to operate the heater inside any vehicle, camper or

 

VALVE BUTTON BEFORE INSERTING LIT MATCH. Repeat step “D”

 

enclosure.

 

for each burner.

B. FOR OUTDOOR USE ONLY. Any combustion process

E.

Adjust heat output by turning knob to desired position.

 

requires and consumes oxygen, and will produce carbon

 

F.

If burner does not light within 30 seconds, turn the heater’s

 

monoxide.

 

 

regulator knob to “off” (clockwise) and allow at least five

C. WARNING: provide ample ventilation. This heater con-

 

 

minutes for gas to dissipate before attempting to relight.

 

sumes air (oxygen). Do not use this heater in unventilated

 

 

G.

NOTE: Should the orifice become clogged as indicated by low

 

structures to avoid endangering your life. Provide additional

 

ventilation for any additional fuel-burning appliances and

 

volume of gas when operating on “Hi” with a full cylinder, or

 

 

should the heater fail to operate properly for any reason, return

 

additional occupants.

 

 

 

the heater to the dealer or the address given on back page for

 

 

 

4. MINIMUM CLEARANCE FROM

 

repair or replacement. DO NOT ATTEMPT TO REPAIR OR TAMPER

 

WITH HEATER.

 

COMBUSTIBLE MATERIALS (Fig. 3)

H.

COOKING: DO NOT USE THIS HEATER FOR COOKING.

 

 

A.WARNING: This heater is an unvented appliance and MUST be used ONLY in a well ventilated area. NEVER attempt to operate the heater inside any vehicle, camper or enclosure.

B.WARNING: To avoid injury or property damage never allow clothing, tents or other combustible material within 36” of the heater. This heater must be located at least 32” above the floor level when in use. Never operate the heater when sleeping.

C.WARNING: Never direct the heat output of this heater toward any propane tank within 20 feet.

BTU/HR. RATING

NORMAL

CLEARANCES TO COMBUSTIBLES

 

MODEL

GAS

 

OPERATING

FROM C.L. OF

 

 

 

 

NO.

PROPANE

PROCEDURE

HTR. TO FLOOR

SIDES

REAR

CEILING

FRONT

MH45T

45,000

 

Vertical

32”

36"

36"

48”

48"

 

 

 

 

 

 

 

 

 

Figure 3

Figure 4

Mr. Heater Gas-Fired Infra-Red Portable Heater

5

Operating Instructions and Owner’s Manual

Page 5
Image 5
Mr. Heater MH45T Assembly Procedure, Lighting Instructions, Ventilation, Minimum Clearance From, COMBUSTIBLE MATERIALS Fig