SECTION 3: ASSEMBLING YOUR LAWN MOWER

IMPORTANT: This unit is shipped without gasoline or oil in the engine. Be certain to service engine with gasoline and oil as instructed in the separate engine manual before operating your mower.

NOTE: Reference to right or left hand side of the mower is observed from the operating position.

Removing Unit From Carton

Remove staples, break glue on top flaps, or cut tape at carton end and peel along top flap to open carton.

Remove loose parts if included with unit (i.e., operator’s manual, etc.)

Carefully cut along corners, lay carton down flat, and remove packing material.

Roll or slide unit out of carton and check carton thoroughly for loose parts.

Disconnecting Spark Plug Wire

Before setting up your lawn mower, disconnect the spark plug wire from the spark plug and ground against the engine. See Figure 1.

Bolt

 

 

Spark Plug

 

Wire

Spark

 

Plug Wire

Spark Plug

Figure 1

Setting Up Your Lawn Mower

Lift up and pull back on the upper handle to raise the handle into the operating position. Make certain the lower handle is seated securely into the handle bracket assemblies. To secure the upper and lower handle, tighten the wing nuts near the top of lower handle (carriage bolts must be seated properly into the handle).

Tighten the wing nuts at the end of the lower handle to secure the handle to handle bracket assemblies. See Figure 2.

NOTE: Your mower is shipped with the handle in the higher position. If you wish to lower the height of the handle, refer to the Adjustment Section.

Wing Nuts

Lower

Handle

Handle

Bracket

Assemblies

Figure 2

Fasten the cables to the lower handle with the cable tie found on the lower handle. Pull the cable tie tight and trim off the excess. See Figure 3.

Cable Tie

Lower

Handle

Figure 3

If not already, move rope guide to the first hole above the lower handle on right side. The wing nut loosens and secures the rope guide. See Figure 4.

Starter

Upper Handle

Rope

 

 

Wing Nut

Rope

Guide

Lower

Handle

Figure 4

With the spark plug wire disconnected and grounded, hold the blade control handle against the upper handle, and pull the starter rope out of the engine. Release the blade control handle. Slip the starter rope into the rope guide. Tighten the wing nut.

NOTE: This manual represents two different model series. Model 260 series comes with the side discharge assembly on the unit and a snap on mulching baffle. The 270 series comes with the mulching baffle on the unit and a snap on side discharge chute.

7

Page 7
Image 7
MTD 260 Thru 279 manual Assembling Your Lawn Mower, Removing Unit From Carton, Disconnecting Spark Plug Wire

260 Thru 279 specifications

The MTD 260 to 279 series represents a range of robust and versatile outdoor power equipment designed to cater to various lawn care and maintenance tasks. These models are tailored for both residential and commercial users, offering reliable performance through advanced engineering and cutting-edge technologies.

One of the standout features of the MTD 260 to 279 series is the powerful engine configuration. These machines are equipped with either gas or electric engines, ensuring efficient operation tailored to user preferences and environmental considerations. The gas models typically feature reliable four-stroke engines, known for their durability and ability to handle larger areas without frequent refueling. In contrast, the electric variants provide a quieter, emissions-free alternative, perfect for residential neighborhoods.

In terms of cutting technology, this series employs a range of deck sizes and cutting systems, providing users with options suited to their specific lawn dimensions and grass types. The precision-cut decks ensure even grass height, promoting healthier lawn growth. Furthermore, many models within this series come with adjustable cutting heights, allowing users to customize their mowing experience based on seasonal changes and grass growth rates.

Another significant aspect of the MTD 260 to 279 series is the emphasis on user convenience and comfort. Ergonomically designed handles and controls enhance ease of use, reducing fatigue during longer operation periods. Many models also come with features like self-propulsion, allowing users to navigate diverse terrains effortlessly.

Durability is a hallmark of the MTD brand, and these models reflect that commitment with robust construction using high-quality materials. Reinforced decks and weather-resistant components ensure longevity and withstand varying outdoor conditions, making them an excellent investment for users.

Further enhancing the appeal of the MTD 260 to 279 series is the integration of modern technologies. Some models incorporate smart features like LED headlights for improved visibility during low-light conditions and advanced safety systems that minimize the risk of accidents.

In summary, the MTD 260 to 279 series presents a comprehensive solution for lawn care enthusiasts. With powerful engines, versatile cutting options, user-centric design, and modern technologies, these models are engineered to deliver exceptional performance, making yard work more efficient and enjoyable. Whether for residential use or professional landscaping, the MTD 260 to 279 range stands out as a reliable choice for managing lawn care needs.