•If you placed plastic film under the gas cap earlier, remove it now.

Trigger Cables

 

Shift Arm

Drive Actuator

Auger Actuator

Bracket

 

Bracket

 

Hex Nut &

 

Cupped

Hex Gear Shaft

Washer

 

 

Rubber

 

Friction

 

Wheel

 

Drive Plate

Figure 11

Auger Control

Refer to instructions on page 6 to adjust the auger control. Make certain to check for correct adjustment as instructed before operating the snow thrower.

Skid Shoe

The space between the shave plate and the ground can be adjusted by raising or lowering the skid shoes.

For close snow removal, as when using on a smooth concrete or asphalt driveway, place the skid shoes in the low position. Use the middle or high position when the area to be cleared is uneven. When operating on gravel, always put skid shoes in the high position. See Figure 12.

Adjust skid shoes as follows:

•Loosen, but do not remove, the three hex nuts which fasten the skid shoe to the auger housing.

•Raise or lower the skid shoe to desired position.

•Retighten the hex nuts loosened earlier.

•Repeat on the other side of the snow thrower.

Chute Assembly

The distance snow is thrown can be adjusted by adjusting the angle of the chute assembly. Refer to page 8 for instructions.

The remote chute control cables have been pre- adjusted at the factory. Move the remote chute lever on

Shave Plate

Carriage Bolts

Skid

Shoes

High

Low

Hex Nuts

the control panel back and forward to adjust angle of the chute assembly.

Figure 12

NOTE: Make certain the bottom surface of skid shoe is flat against the ground to avoid uneven wear

SECTION 6: MAINTAINING YOUR SNOW THROWER

WARNING: Before lubricating, repairing, or inspecting, disengage all clutch levers and stop engine. Wait until all moving parts have come to a complete stop. Disconnect the spark plug wire and ground it against the engine to prevent unintended starting.

warranty, operator must maintain the snow thrower as instructed in this manual.

•Some adjustments will have to be made periodically to maintain your unit properly.

•Periodically check all fasteners and hardware to make sure these are tight.

General Recommendations

•Always observe safety rules when performing any maintenance.

•The warranty on this snow thrower does not cover items that have been subjected to operator abuse or negligence. To receive full value from the

Lubrication

Drive and Shifting Mechanism

•At least once a season or after every 25 hours of operation, remove rear cover. Lubricate any chains, sprockets, gears, bearings, shafts, and the shifting

12

Page 11 Page 13
Page 12
Image 12
MTD 31AE993I401 manual Maintaining Your Snow Thrower
Page 11 Page 13

31AE993I401 specifications

The MTD 31AE993I401 is a powerful riding lawn mower designed to deliver an efficient and reliable lawn care experience. This machine is tailored for homeowners looking for a robust and easy-to-use solution for maintaining their yards. With its practical features and advanced technologies, the MTD 31AE993I401 stands out in the competitive landscaping market.

One of the most notable features of the MTD 31AE993I401 is its impressive 18 HP engine, which provides ample power to tackle challenging terrains and dense grass. The engine is designed for efficiency, ensuring that users can complete their mowing tasks without frequently refueling. The mower's hydrostatic transmission allows for smooth and seamless acceleration, enabling operators to adjust their speed effortlessly while maneuvering around obstacles.

The cutting deck is another defining characteristic of the MTD 31AE993I401. With a wide 42-inch cutting width, the mower covers a larger area in fewer passes, making it ideal for medium to large lawns. The deck height adjustment feature offers versatility, allowing users to customize the cutting height to suit their lawn’s specific needs. This is particularly beneficial for maintaining a healthy grass height that promotes optimal growth.

Comfort is a priority in the design of the MTD 31AE993I401. It features an ergonomic seat with armrests, providing users with a comfortable riding experience, even during extended mowing sessions. The intuitive control panel ensures that all essential functions are easily accessible, making operation straightforward for both new and experienced users.

To enhance durability and longevity, the MTD 31AE993I401 is built with robust, high-quality materials. Its steel frame adds to its resilience, ensuring the mower can withstand the rigors of regular use.

Additionally, the MTD 31AE993I401 incorporates innovative technologies for ease of use and maintenance. The mower is equipped with a reliable starting system, reducing the hassle of manual start-ups. Its easy-to-reach maintenance points simplify service tasks, making it easier for owners to keep the mower in prime condition.

In summary, the MTD 31AE993I401 riding lawn mower combines power, comfort, and durability into a single machine. Its efficient engine, wide cutting deck, and user-friendly features make it a top choice for those seeking an effective lawn care solution. Whether you're tackling a small yard or managing expansive lawns, the MTD 31AE993I401 delivers exceptional performance and reliability.
Top Page Image Contents