If the oil level is low, add Cub Cadet hydraulic oil. Loosely position a funnel in the fill hole so that there is enough clearance around the fun- nel to allow the transmission to vent while the oil is poured into the transmission. Fill ONLY to the full mark, never overfill the transmission.

NOTE: Always use Cub Cadet hydraulic oil to ensure correct formulation. Substitute oils could affect performance and may cause damage to the transmission.

Reinsert the oil fill plug/dipstick into the transmission housing and turn clockwise until tight.

CHANGING TRANSMISSION/HYDRAULIC SYSTEM OIL

Change the hydrostatic transmission/hydraulic system oil and filters after every 200 hours of operation. The dry capacity of the transmission/ hydraulic system is approximately 26 quarts.

Change the transmission/hydraulic system oil as follows:

Operate the tractor for a short period to warm the oil to the normal operating temperature. Place the tractor on a level surface, engage the parking brake, and stop the tractor engine.

Remove any belly mounted attachments.

Clean the area around the transmission drain plug and the oil fill plug/dipstick to prevent debris from entering the transmission. Refer to Figure 45 and Figure 46.

HYDROSTATIC

HYDRAULIC

SYSTEM

OIL FILTER

FILTER

(723-3014)

(723-0405)

 

TRANSMISSION

DRAIN PLUG

Viewed from beneath the Tractor

Figure 46

Place a suitable container(s) beneath the front of the transmission housing.

Remove the oil fill plug/dipstick to help vent the transmission, then remove the drain plug and allow the transmission oil to drain into the container(s). Reinstall the drain plug after draining the oil. See Figure 46.

Dispose of used oil in an environmentally safe manner. If necessary, contact your area EPA office for proper disposal proce- dures and recycling center locations.

Clean around the base of the hydrostatic transmission oil filter and remove the filter by turning it counterclockwise. See Figure 46.

Apply a light coating of clean transmission oil to the gasket of the new filter. Install the filter by turning it clockwise, by hand, until the gasket contacts the filter base on the transmission housing; then tighten the filter an additional 1/2 to 3/4 turn.

Clean around the base of the hydraulic system oil filter and remove the filter by turning it counterclockwise. Refer to Figure 46.

Apply a light coating of clean transmission oil to the gasket of the new filter. Install the filter by turning it clockwise, by hand, until the gasket contacts the filter base on the transmission housing; then tighten the filter an additional 1/2 to 3/4 turn.

Loosely position a funnel in the oil fill hole so that there is enough clearance around the fun- nel to allow the transmission to vent while the oil is poured into the transmission. Fill ONLY to the full mark on the dipstick, never overfill the transmission.

NOTE: Always use Cub Cadet hydraulic oil and filters to ensure correct formulation and filtering capacity. Substitute oils and/or filters could affect performance and may cause damage to the transmission.

Reinsert the oil fill plug/dipstick into the transmission housing and turn clockwise until tight.

Start the engine and allow it to run for a few minutes. Shut the engine off, then check for leaks and recheck the oil level in the transmission housing.

35

Page 35
Image 35
MTD 7304 manual Changing TRANSMISSION/HYDRAULIC System OIL

7304 specifications

The MTD 7304 is a powerful and efficient lawn mower that is designed for both residential and commercial use. Known for its reliability and performance, the MTD 7304 has become a popular choice among homeowners and landscape professionals alike. This mower is equipped with a range of features and technologies that enhance its functionality, making yard maintenance an easier task.

One of the standout features of the MTD 7304 is its robust engine. Powered by a durable, high-performance engine, this mower ensures consistent power delivery, making it suitable for tackling a variety of grass types and terrains. The engine is engineered for fuel efficiency, which not only helps in reducing operating costs but also minimizes environmental impact.

The cutting deck of the MTD 7304 is another highlight, typically measuring around 30 inches. This size strikes a perfect balance between maneuverability and cutting capacity, allowing users to navigate through narrow spaces while still covering significant areas in a single pass. The mower also incorporates adjustable cutting heights, providing flexibility for different grass lengths and conditions.

Equipped with advanced technology, the MTD 7304 includes an easy-to-use electric start feature. This eliminates the hassle of pull-starting, making the mower accessible to users of all ages. The mower is also designed with a user-friendly control panel, featuring intuitive controls that allow for effortless operation and adjustments while mowing.

Durability is a key characteristic of the MTD 7304, with high-quality construction materials that can withstand the rigors of regular use. The sturdy frame and components contribute to the mower's long lifespan, ensuring that it remains a reliable choice for years to come. Additionally, the mower often features a robust warranty that reflects the manufacturer's confidence in its durability.

Another notable aspect of the MTD 7304 is its ergonomic design. Comfortable handles and adjustable height options provide ease of use, reducing fatigue during extended mowing sessions. The compact design also aids in storage, allowing users to store the mower in smaller spaces without any hassle.

In summary, the MTD 7304 is a versatile mower that combines power, efficiency, and durability. With its advanced features, user-friendly technologies, and ergonomic design, it stands out as a top choice for those seeking effective lawn care solutions. Whether for a residential lawn or commercial landscaping, the MTD 7304 delivers exceptional performance, making it a valuable addition to any outdoor maintenance toolkit.