MAINTENANCE AND REPAIR INSTRUCTIONS

Clean Air Filter

The condition of the air filter is important to the operation of the unit. A dirty air filter will restrict air flow and change the air/fuel mixture. This is often mistaken for an out of adjustment carburetor. Check the condition of the air filter before adjusting the idle speed screw. Refer to Air Filter Maintenance.

Adjust Idle Speed Screw

If, after checking the fuel mixture and cleaning the air filter, the engine still will not idle, adjust the idle speed screw as follows:

1.Start the engine and let it run at a high idle for a minute to warm up. Refer to Starting/Stopping Instructions.

WARNING: The cutting attachment will spin

during idle speed adjustments. Wear protective clothing and observe all safety instructions to prevent serious personal injury.

2.Release the throttle trigger and let the engine idle. If the engine stops, insert a small phillips screwdriver into the hole in the air filter/muffler cover (Fig. 27).

Turn the idle speed screw in, clockwise, 1/8 of a turn at a time (as needed) until the engine idles smoothly.

3.If the engine appears to be idling too fast, turn the idle speed screw counterclockwise 1/8 of a turn at a time (as needed), to reduce idle speed.

Idle Speed Screw

Checking the fuel mixture, cleaning the air filter, and adjusting the idle speed should solve most engine problems. If not and all of the following are true:

•the engine will not idle

•the engine hesitates or stalls on acceleration

•there is a loss of engine power

Have the carburetor adjusted by an authorized service dealer.

WARNING: To prevent serious personal injury,

make sure the cutting attachment has stopped rotating after you turn it off and before you set it down.

REPLACING THE SPARK PLUG

Use a Champion RDJ7Y spark plug, or equivalent. The correct air gap is 0.020 inch (0.5 mm). Remove the plug after every 25 hours of operation and check its condition.

1.Stop the engine and allow it to cool. Grasp the plug wire firmly and pull it from the spark plug.

2.Clean around the spark plug. Remove the spark plug from the cylinder head by turning a 5/8-inch socket counterclockwise.

3.Replace a cracked, fouled or dirty spark plug. Set the air gap at 0.020 in. (0.5 mm) using a feeler gauge (Fig. 28).

WARNING: Do not sand blast, scrape or clean

electrodes. Grit in the engine could damage the cylinder.

4.Install a correctly-gapped spark plug in the cylinder head. Tighten by turning the 5/8-inch socket clockwise until snug.

If using a torque wrench torque to:

110-120 in.•lb. (12.3-13.5 N•m) Do not over tighten.

0.020 in.

(0.5 mm)

Fig. 27

Fig. 28

15

Page 14 Page 16
Page 15
Image 15
MTD MT700 manual Replacing the Spark Plug, Clean Air Filter, Adjust Idle Speed Screw
Page 14 Page 16

MT700 specifications

The MTD MT700 is a highly sophisticated tractor designed to meet the demands of modern agriculture. Its advanced engineering showcases a blend of power, efficiency, and flexibility, making it a valuable asset for farmers and agricultural professionals.

One of the standout features of the MTD MT700 is its powerful engine. Equipped with a robust powertrain, the MT700 delivers impressive horsepower, providing operators with the capability to tackle heavy workloads and challenging terrains. This reliability ensures that farmers can depend on the tractor for at various tasks such as plowing, tilling, and hauling.

The MT700 incorporates cutting-edge technology to enhance performance and operational efficiency. It features a highly responsive hydrostatic transmission, allowing for smooth acceleration and deceleration. This transmission system enables operators to maintain precise control over speed and torque, essential for various farming applications. Moreover, the tractor's intuitive control system streamlines operation, reducing the learning curve for new users and increasing productivity.

A notable characteristic of the MT700 is its innovative design aimed at comfort and convenience. The spacious cab is ergonomically designed with user-friendly controls and ample visibility, allowing operators to work long hours without fatigue. The climate-controlled environment ensures comfort regardless of external conditions, which is crucial for prolonged operations in the field.

Additionally, the MT700 is designed for versatility. Its mounting system accommodates a wide range of implements, from seeders to mowers, making it suitable for various agricultural tasks. This adaptability further enhances its utility on diverse farms.

Furthermore, the MTD MT700 is built with durability in mind. Constructed with high-quality materials and components, it withstands the rigors of demanding agricultural operations. The tractor's maintenance-friendly design facilitates easy servicing, ensuring that it remains in optimal working condition year-round.

In summary, the MTD MT700 tractor represents the pinnacle of agricultural engineering, combining powerful performance, advanced technologies, and user-centric design. Farmers and agricultural professionals can rely on this tractor to enhance productivity and efficiency, making it an essential tool in modern farming operations. With its impressive features and capabilities, the MTD MT700 is poised to transform the way agriculture is conducted, setting new standards in the industry.
Top Page Image Contents