Highlights

DID Enabler. The CallFinder DID adapter allows non-DID enabled systems to support auto-call routing, eliminating the need for a receptionist or auto-attendant menu dialing. Direct Inward Dialing (DID) allows a PBX or key telephone system to use a block of telephone numbers, via two DID lines, for direct dialing to extensions. Callers simply dial

a typical telephone number (no special procedures are required). The CallFinder DID adapter automatically converts the DID phone number to analog DTMF tones and delivers it to the PBX to ring the called party's extension.

The CallFinder DID adapter can interface to most call processing systems capable of detecting ringing, loop current and providing on/off hook control. It supports two DID circuits that can be programmed to support wink-start, immediate-start or delay dial service types. In addition, it offers answer supervision and passes audio notification, from the switch, back to the central office (audio ringback and busy).

Loop Start/CO Port Connections. The CallFinder DID adapter can also connect to the PBX/KTS via a Loop Start/CO port (FXO). With this setup, an answering device, such as an Auto Attendant, is required. When a DID call is received, the CallFinder DID adapter will check its table, ring into a Loop start trunk, and deliver the extension number via DTMF tones. The PBX delivers the call directly to the end- user automatically bypassing the auto attendant menu. In addition, because it is delivered as an outside call, the user now has the ability to offer call detail reports through call accounting software.

Analog Extension/Station Port Connections. If you don't have any available CO ports, the CallFinder DID adapter can also connect to the PBX/KTS via an analog extension/station port (FXS). When using this type of connection, the PBX will deliver the call to the end-user as an internal call. Typically the user would program the PBX/KTS to display "DID Call" to the other station phones.

Comprehensive Service and Support. The Multi-Tech commitment to service means we provide a two-year product warranty and service that includes free telephone technical support, 24-hour web site and ftp support.

Specifications

Connectors

4 RJ-11 (2-DID, 2-FXS/FXO)

1 10/100BaseT Ethernet (configuration & management)

DID (analog loop start DID lines)

Service Types: Wink-start; immediate-start; delay dial

Signaling Types: DTMF

FXS

Ring Voltage: 44V RMS sine wave @ 20 Hz

Battery Voltage: 48V current limited @ 23mA

Physical Description

6" L x 6.4" W x 1.2" H; 1.2 lb.

(15.2 cm x 16.3 cm x 3.0 cm: 544g)

Power Supplies

100-240VAC, 47-60 Hz

Operating Environment

Temperature Range: +32° to +120° F (0° to +50° C)

Humidity Range: 20-90% noncondensing

Certifications

EMC: FCC Part 15 Class A, EN 55022, EN 55024

Safety: cUL, EN 60950, UL 60950

Telecom: 47CFR Part 68, CS03

Ordering Information

Product

Description

Region

CF220-DID

2-Port DID-to-Analog Adapter

US/Can

Made in Mounds View, MN, U.S.A.

Features and specifications are subject to change without notice.

Trademarks / Registered Trademarks: CallFinder, Multi-Tech, and the Multi-Tech logo: Multi-Tech Systems, Inc. / All other products and technologies are the trademarks or registered trademarks of their respective holders.

World Headquarters

EMEA Headquarters

 

Tel:

(763) 785-3500

Multi-Tech Systems (EMEA)

Multi-Tech Systems (EMEA)

 

(800) 328-9717

United Kingdom

France

www.multitech.com

Tel: +(44) 118-959 7774

Tel: +(33) 1 64 61 09 81

 

 

 

 

6/07

86002055

Copyright © 2007 by Multi-Tech Systems, Inc. All rights reserved.

 

Page 2
Image 2
Multi-Tech Systems EN55024, UL60950, EN60950, EN55022 warranty Highlights, Specifications, Ordering Information