Manuals / Multiquip / Kitchen Appliance / Mixer

Multiquip EM-900S operation manual Step

Models: EM-900S

1 32
Download 32 pages 61.71 Kb
Page 10
Image 10

TOWING — Before towing, check with local and state laws for proper compliance.

The tow bar and chain must be properly attached to the mixer and towing vehicle prior to towing. Refer to the following installation instruction:

Step 1. Insert the Draw Bar into the main frame. Secure, utilizing the ¾" bolt (grade 5) and nylock nut.Tighten to 100 foot pounds.

Step 2. Install the chain through the hole located between the frame gusset and frame angle. Loop the chain together and place under the Draw Bar. Secure with connector link.

Step 3. Extend the chain along the length of the Draw Bar, remove excess chain (slack) and secure to bottom connector link. Secure the chain to the towing vehicle, using the connector link.

NOTE: It is critical that the length of chain be properly adjusted to prevent the Draw Bar and front mixer stand from dropping to the ground (contact) in the event the Draw Bar becomes disconnected from the towing vehicle.

DANGERBEFORE TOWING

BALL HITCH COUPLER

1.Check vehicle hitch, ball, and coupler for signs of wear or damage. Replace any parts that are worn or damaged before towing.

2.Use only the 2" ball diameter as indicated on your coupler. Use of any other ball diameter will create an extremely dangerous condition which can result in separation of the coupler and ball or ball failure.

3.Be sure the coupler is secured to the hitch ball and the lock lever is down tight and locked.

Recheck tightness again after towing about 50 miles.

4.Check that trailer safety chains are properly connected.

RECOMMENDED MAINTENANCE

1.Smear ball socket and clamp face with chassis grease. Periodically oil pivot points and solutions surfaces of coupler with SAE 30 wt. motor oil.

2.When parking or storing your trailer. Keep the coupler off the ground so dirt will not build up in the ball socket.

EM-900S & 900P — OPERATIONS

STEP 1

DRAW BAR

BOLT & NUT

INSERT CHAIN THROUGH

STEP 2

THE HOLE

 

 

DRAW BAR

FRAME ANGLE

 

FRAME GUSSET

CONNECTOR LINK

STEP 3

VEHICLE

CONNECTOR LINK

DRAW BAR

REMOVE EXCESS CHAIN (SLACK)

BOTTOM CONNECTOR LINK

SAFETY CHAIN

P/N 3148

CONNECTOR LINK

P/N 01004

DANGER

If housing is deformed,

 

replace complete coupler.

 

USE ONLY GENUINE

 

FULTON REPAIR KITS.

PAGE 10 — ESSICK EM-900S & 900P — PARTS & OPERATION MANUAL — REV. #7 (06/26/01)

Page 9 Page 11
Page 10
Image 10
Multiquip EM-900S operation manual Step
Page 9 Page 11

EM-900S specifications

The Multiquip EM-900S is a robust and efficient electric concrete mixer designed to cater to the needs of construction professionals and DIY enthusiasts alike. Known for its reliability and performance, the EM-900S stands out for its user-friendly features and advanced technologies aimed at enhancing productivity on job sites.

One of the main highlights of the EM-900S is its powerful 1.5 horsepower electric motor. This motor is designed for optimal performance, ensuring that the mixer can handle various concrete mixes with ease. Its direct drive system minimizes maintenance needs and prevents slippage, making it a dependable choice for users.

The EM-900S features a large 9-cubic-foot capacity drum, allowing for substantial mixing of materials. This generous size means fewer batches are required, saving both time and effort. The drum is constructed from high-quality steel, ensuring durability and longevity in demanding work environments.

Another notable characteristic is the EM-900S's ergonomic design. Equipped with a comfortable handle and well-balanced frame, the mixer is easy to maneuver on job sites. This design not only enhances usability but also improves safety during operation, allowing operators to mix and pour materials efficiently.

The EM-900S is also equipped with a unique tilting mechanism. This allows for precise control when pouring concrete, enabling users to achieve an accurate pour while minimizing waste. The mixer can be tilted at various angles to accommodate different project requirements.

For added convenience, the EM-900S comes with large pneumatic wheels that enhance mobility across rough terrain. These heavy-duty wheels provide excellent traction and make it easy to transport the mixer to different locations without hassle.

Additionally, the EM-900S boasts an integrated safety switch and emergency stop feature, ensuring that users can operate the machine safely under various conditions. This focus on safety is a crucial consideration for professionals working in the construction industry.

Overall, the Multiquip EM-900S electric concrete mixer combines powerful performance, user-friendly features, and advanced design elements. With its ample capacity, durable construction, and safety features, the EM-900S is an ideal choice for both commercial and residential projects, enhancing efficiency and productivity on the job site. Whether mixing concrete for foundations, slabs, or other applications, the EM-900S is built to deliver reliable results every time.