Murphy L150 specifications Description, Applications, Specifications

Level SWICHGAGE® Series For Engine Liquids

L-6795B

Revised 10-99

Catalog Section 15

(00-02-0058)

L150/EL150K1 Series for Coolants, Lube Oils, Fuel and Hydraulic Fluid

Description

The L150 Series Level SWICHGAGE® is a combination liquid level gauge and low limit switch; each unit includes (1) a chamber with pivotal float, (2) an indicating dial with pointer, and (3) a low level contact. When properly installed and maintained, the float operates the pointer which, in turn, both indicates level during nor- mal operation, and closes a switching circuit if the level falls to the low-limit set point.

Applications

The primary use of the L150/EL150K1 is for engine cooling sys- tems, surge or expansion tanks, condenser radiator or vapor phase systems, pressurized or atmospheric systems. The Level SWICHGAGE® can also be used to monitor lube oil, hydraulic fluid or diesel fuel reservoirs and activates alarms and/or shut- down at a predetermined minimum level.

These instruments are built for low pressure systems with a maximum of 25 psi (172 kPa) [1.72 bar].

•Monitors level of coolant, lube oil, diesel fuel and hydraulic fluid.

•Indicating Gauge

•Low Limit Switch

•Float Operated

•Explosion-proof model is available.

*

SWICHGAGE ®

Specifications

L150

Case: Die cast aluminum, poly-urethane coat- ed; approximate dimensions; 4-1/2 x 4-3/4 x 2-3/4 in. (114 x 121 x 70 mm).

Mounting Holes: (2) 9/32 in. (7 mm) diameter at 4-1/2 in. (114 mm) on center.

Float: Brass.

Lens: Polycarbonate.

O-rings:Saturated Nitrile, are suitable for coolant or hydrocarbons. Maximum tempera- ture 250°F (121°C).

Gasket: Neo-cork.

Vent Tube: 1/4 x 5 in. (6 x 127 mm) copper cane with 1/4 NPT x 1/4 in. (6 mm) tube fitting.

Contact Rating: 2 A @ 30 VAC/DC.

Wire: (1) 16 AWG x 26 in. (1.5 mm2 x 660 mm) with terminals.

Shipping Weight: 29 oz. (0.82 kg.).

Shipping Dimensions: 5-1/4 x 5-1/4 x 5-1/2 in. (133 x 133 x 140 mm).

1/4 NPT

EL150K1

Case: Die cast aluminum, poly-urethane coat- ed; approximate dimensions; 5 x 4-3/4 x 2-3/4 in. (127 x 121 x 70 mm).

Mounting Holes: (2) 9/32 in. (7 mm) diameter at 4-1/2 in. (114 mm) on center.

Float: Brass.

Lens: Polycarbonate.

O-rings:Saturated Nitrile, are suitable for coolant or hydrocarbons. Maximum tempera- ture 250°F (121°C).

Gasket: Neo-cork.

Vent Tube: 1/4 x 5 in. (6 x 127 mm) copper cane with 1/4 NPT x 1/4 in. (6 mm) tube fitting.

Snap-Switch:SPDT rated 10 A @ 125 VAC; 0.5 A @ 125 VDC; 10 A 30 VDC.

Wire: (3) 18 AWG x 14 in. (1.0 mm2 x 356 mm).

Shipping Weight: 42 oz. (1.2 kg.).

Shipping Dimensions: 5-1/4 x 5-1/4 x 5-1/2 in. (133 x 133 x 140 mm).

1/4 NPT

Snap-Switch

EL150EX

Case: Sand cast aluminum, painted;

approximate dimensions; 6-1/2 x 5-3/4 ® x 5-1/4 in. (165 x 146 x 133 mm).

Mounting Holes: (2) 5/16 in. (8 mm) diameter at 5-1/2 in. (140 mm) on center.

Float: 304 Stainless steel.

Lens: Tempered glass.

O-rings:Saturated Nitrile, are suitable for coolant or hydrocarbons. Maximum tempera- ture 250°F (121°C).

Gasket: Neo-cork.

Vent Tube: 1/4 x 5 in. (6 x 127 mm) copper cane with 1/4 NPT x 1/4 in. (6 mm) tube fitting and 1/2 NPT to 1/4 NPT reducer fitting.

Snap-Switch:SPDT rated 10 A @ 125 VAC; 0.5 A @ 125 VDC; 10 A 30 VDC.

Wire: Wired to terminal block.

Shipping Weight: 5 lbs. (2.26 kg.).

Shipping Dimensions: 6-1/2 x 6-3/4 x 6-3/8 in. (165 x 171 x 162 mm).

1/2 NPT	1/2 NPT
Conduit	Explosion-
Connection
	proof Case

Adjustable

Test

Knob

1/2 NPT

Test

Knob

1/2 NPT Conduit

1/2 NPT

(side of case)

1/2 NPT (bottom of case)

CSA Listed for Hazardous Location:

Limit Contact

Class I, Division 1, Group C & D

*Products covered by this bulletin comply with EMC Council directive 89/336/EEC regarding electromagnetic compatibility except as noted.