NCR 7837 - page 60

7837 User’s Guide

7–6

  

Code 39

* On Off

Start / Stop Characters

Transmit * Don’t Transmit

Start/Stop characters identify the leading and trailing ends of the bar code.

You may either transmit, or not transmit Start/Stop characters.

Default =

Don’t Transmit.

Contents

Main Page Section 1 Getting Started Section Page Section 2 Terminal Interfaces Section 3 Output Section 4 Data Editing Section 5 Data Formatting Section 6 Secondary Interface Section 7 Symbologies Industrial Symbology Selections Retail Symbology Selections Section 8 Cloning Page Section 1 Getting Started 7837 Users Guide 11 About This Manual Scanner Identification Label Connecting the Scanner When Powered by Host (Keyboard Wedge) 14 (Default) Page 16 IBM 4683 Ports 5B, 9B, and 17 Interface OCIA Interface NCR OCIA Short Format (8 Bit) Interface 18 NCR OCIA Long Format (9 Bit) Interface Nixdorf OCIA Interface Section 2 Terminal Interfaces 21 Keyboard WedgeConnection 22 Keyboard WedgeSupported Terminals Chart 24 Supported TerminalsChart, continued (Default) Keyboard Country 26 Page 28 Serial Port Connection Default = 9600. 210 RS232 Word Length: Data Bits, Stop Bits, and Parity Default = 7. Default = 1. Default = Even. Page 212 RS232 Handshaking Wand Emulation Connection 214 Wand Emulation TransmissionRate Default = 25 inches/second. 21 Wand Emulation Polarity Wand Emulation Idle Page Section 3 Output 31 Scan Rate Default = 270 s/s. Beeper Volume Beeper Tone Default = Normal. Scan Voting Default = Voting Normal. Reduce Quiet Zone same Default = Short. Default = No Delay. Default = Manual Trigger Default = 2 minutes. Section 4 Data Editing 41 Points to KeepIn Mind Default prefix = None. Default suffix = None 42 ToAdd a Prefix or Suffix: Example: Add a Suffix to a specific symbology ToClear One or All Prefixes or Suffixes: 7837 Users Guide ToAdd a Carriage Return Suffix to all Symbologies ToAdd a Code I.D. Prefix to All Symbologies Page Symbology [ All Symbologies 99 Hex Value Function Code Transmit 48 User Specified Intercharacter Delay Page Section 5 Data Formatting 51 Data FormatEditor Default Data Format setting = none. To Add a Data Format Data FormatEditor Commands Send Commands Move Commands Syntax = F7. 5 Search Commands Miscellaneous Commands Page 56 Section 6 Secondary Interface 61 Secondary Interface or Secondary Code 39 Wand Emulation Page 6 Non Decoded Laser Emulation Idle Default =Disable Default = High. Disabling the Secondary Interface 64 Secondary Trigger Mode Default = Manual Trigger Default = 2 minutes. Codabar Start / Stop Characters Codabar, Check Character with Default = No Check Character. Page Codabar, Message Length Page Page 78 Code 39, Code 39 Append Default = Off. Base 32 Code 39, 710 Full A Default = On. * Interleaved 2 of 5 Check Digit Interleaved 2 of 5 Interleaved 2 of 5, 712 Strict Decoding Code 93 <Default All Code 93 Settings> Code 93 714 Code 2 of 5 <Default All Code 2 of 5 Settings> 2 of 5 IATA Code 2 of 5 <Default All Code IATA 2 of 5 Settings> IATA 2 of 5 716 Matrix 2 of 5 <Default All Matrix 2 of 5 Settings> Page Code 11, 718 Code 128 <Default All Code 128 Settings> Function Character Transmit Default =Off. <GS> Substitution Default =Off. Code 128, 720 Page Telepen, 722 Page Page UPC A, 72 Addenda Required Default = Off. Strict Decoding Page Page Page Page Page Page Page 73 MSI with <Default All MSI Settings> Check Character Default = Validate Type 10, but Dont Transmit. MSI, 734 73 Plessey <Default All Plessey Settings> Plessey 736 China Post Code <Default All China Post Code Settings> Section 8 Cloning 81 Procedure: Clone Destination Bar Code Clone Source Bar Code Page Section 9 Interface Keys 91 Keyboard Function Relationships 92 < i - 9 94 9 Page Section 10 Defaults 101 Resetting the FactorySettings Factory Default Settings RS-232 Selections 102 Output Selections Data Editing Selections Data Formatter Selections Secondary Interface Selections 10 Code 39 Selections Interleaved 2 of 5 Selections Code 93 Selections Code 2 of 5 Selections 104 10 UPC A UPC E EAN/JAN 13 EAN/JAN 8 106 Section 11 Specifications 111 Product Specifications Page Section 12 Customer Support Page Agency Compliance Statements FCC Class B Compliance Statement shielded Canadian Notice Page Page Page Page Programming Chart Page