Installing the Booster with the
Optional Power Injector
Note: As noted in the illustration below, be sure to disconnect the DC power adapter from the ANT24BNA Booster for 802.11b, and connect it to the NETGEAR ANT24BDC Power Injector.
|
|
| Current antenna |
|
|
| Do NOT remove |
| Connect | Wireless unit |
|
| ETHERNET |
| |
| Antenna |
| |
| RESET |
| |
| cable |
|
|
NETGEAR |
| Primary | Secondary |
Antenna cable |
|
|
|
(short or medium) |
|
| |
Antenna | Connect |
|
|
e. g. NETGEAR | Antenna |
|
|
ANT24O5 | cable |
|
|
Injector NETGEAR |
|
|
|
ANT24BDC
Connect
DC cable
Specifications
| Description | NETGEAR 500mW | ||||
| Booster for 802.11b, with Two | |||||
|
|
|
| Female Reverse SMA Connectors | ||
|
|
|
|
|
|
|
|
|
|
|
|
| |
| Frequency Range |
| 2400 to 2500 MHz |
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| Operating Mode |
| TDD Burst Mode |
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 600 Watts TVS @ 6VDC | |||
| DC Surge Protection |
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
| |
| Current Drain (TDD Mode) |
|
| 700 mA type. @ 6VDC |
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Transmit Power |
| 26.5 dBm minimum |
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| Transmit Input Power |
| + 5 dBm minimum |
|
| |
|
|
|
|
|
| |
|
|
|
|
| ||
|
|
|
| |||
| Transmit Ramp Up Time |
| 3 µs maximum |
| ||
|
|
|
|
|
|
|
Connect Antenna cable
Do NOT connect | DC Block NETGEAR | |
DC cable | ||
|
Connect Antenna cable
| Receiver Gain | 10 dB typical | ||
|
|
|
|
|
|
|
|
|
|
| Receiver Frequency Response |
| ±1 dB over operating range |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Receiver Noise Figure |
| 5 dB maximum |
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
| Receiver Ramp Down Time |
| 3 µs maximum |
|
|
|
|
|
|
|
|
| ||
| Material | ABS | ||
| 500 mW Booster ANT24BNA | Connect |
|
NETGEAR |
| NETGEAR Antenna | |
| Antenna | ||
Antenna |
| cable (medium or long) | |
| cable | ||
cable (short) |
|
| |
|
|
|
|
| Color |
|
|
| White |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Device Size (l x w x h) |
|
|
| 130 x 75 x 37 mm (5.1 x 3.0 x 1.5 in) |
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Weight |
|
|
| 5.0 g/1.1 lbs (including DC adapter) |
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| RF Connector Type |
|
|
| SMA female reverse (2x), 1 for connection to antenna, |
|
|
|
|
|
| 1 for connection to ME103 wireless access point |
| |
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| RF Connector Impedance |
|
|
| 50 ± 5 Ohms |
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
| ||
|
| RF Connector Dielectric |
| 750 VRMS maximum |
| ||
|
| Withstanding Voltage |
|
|
| ||
|
|
|
|
| |||
|
|
|
|
|
| ||
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
| RF Connector Insertion Loss |
| 0.2 dB |
| ||
|
|
|
|
|
|
|
|
6 | 7 |
