![](/images/new-backgrounds/1149846/1498463x1.webp)
4
LAUNCH YOUR BROWSER
This section describes the steps required to configure your router using a web browser such as Microsoft Internet Explorer or Netscape Navigator. This will provide a basic configuration for Internet access.
1.From any PC on your local network, launch your web browser.
2.In the Address box of your browser, type http://192.168.0.1 and press ENTER.
3.A
If your router’s configuration password has been previously changed from the factory default of 1234, enter the current password.
4.At the opening screen, select WIZARD SETUP.
5.In the first Wizard screen, enter your account’s Host Name and Domain Name.
6.Click Next to go to the ISP Parameters screen.
This screen determines whether a login program will be run.
a.If your service provider does not require a login program, leave Encapsulation as Ethernet and proceed to Step 7.
b.If your service provider uses PPPoE, select Encapsulation as PPPoE, and enter these additional parameters:
–If your connection supports multiple ISPs, enter the Service Name of the one you use. Otherwise leave Service Name blank.
– Enter the user name and password provided by your ISP. These fields are case sensitive.
–If you wish to change the login timeout, enter a new value in seconds. Proceed to Step 7.
c.If your service provider is RoadRunner AND you are required to run a RoadRunner login program, leave Encapsulation as Ethernet and select Service Type as either
–If your cable modem is Toshiba, select
– Enter the user name and password provided by your ISP. These fields are case sensitive.
–If RoadRunner provided an authentication server address, enter it as Login Server IP address. Otherwise, leave this field as 0.0.0.0.
Not all RoadRunner regions require a login program. If your region does not require a login, leave Service Type as Standard.
7. Click on Next to go to the final Wizard screen shown below.
a. WAN IP Address Assignment: Unless your ISP has assigned a fixed permanent IP address for your use, select “Get automatically from ISP”. Otherwise, enter your IP Address, Subnet Mask, and the IP Address of your ISP’s gateway router.
b.DNS Server Address Assignment: If you know that your ISP does not automatically transmit DNS addresses to the router during login, select “Use this server” and enter the IP address of the ISP’s DNS server.
A DNS server is a host on the Internet that translates Internet names (such as www addresses) to numeric IP addresses. Typically your ISP transfers the IP addresses of one or two DNS servers to your router during login. If the ISP does not transfer an address, you must obtain it from the ISP and enter it manually here. If you enter an address here, you should reboot your PCs after configur- ing the router.
c.WAN MAC address: If your ISP allows access by only one specific PC’s Ethernet MAC address, select “Spoof this PC’s MAC address” and enter the IP address of that PC.
–For convenience, the IP address of the PC you are now using should already appear. If this is not the PC whose MAC address is to be used, enter that PC’s IP address.
–Some ISPs will register the Ethernet MAC address of the network interface card in your PC when your account is first opened. They will then only accept traffic from the MAC address of that PC. This feature allows your router to masquerade as that PC by using its MAC address.
8.Click Finish.
5-
TEST YOUR CONNECTION
Accessing the Internet
Click the NETGEAR Web site address to test your Internet connection.
When your router and PCs are configured correctly, your router automatically accesses the Internet when one of your LAN devices requires access. It is not necessary to run a dialer application, such as
To access the Internet:
1.From the PC connected to your router, launch a browser such as Microsoft Internet Explorer or Netscape Navigator.
You should see the Internet LED blink, indicating communication to the ISP. The browser should begin to display a Web page.
If you have trouble accessing the Internet, refer to the “Troubleshooting” section of this guide.
Configuring for Content Filtering and Reporting
After you have successfully configured your router for Internet access, you can configure it for content fil- tering and reporting by following these steps:
1.
2.Click Advanced, then Security. To receive logs and alerts by
a.Select the
b.Enter the
c.Select when you would like to receive logs and alerts.
d.Click Apply.
3.To specify blocking of keywords in Web site names, or blocking of Internet domains:
a.Click the Keywords tab.
b.Click the Enable Keyword Blocking checkbox.
c.Enter the keywords or domain names that you wish to block access to. For each entry, type the entry and click Add Keyword.
d.Click Apply.
For more information on configuring the content filtering and reporting features of your router, refer to the Reference Guide for the Model RO318 Cable/DSL Security Safe Router in the enclosed Model RO318 Resource
6 ENJOYBEINGCONNECTED!
Features
Your RO318 Cable/DSL Security Router provides you with the following key features:
•Stateful Packet Inspection (SPI) for Denial of Service (DoS) attack protection from hackers
•Customized Web content filtering capability, based on
•
•Shared,
•Provides VPN
•
•Integrated
•Visual monitoring of router status and activity
•Compatibility with Windows, Macintosh, and Linux operating systems
•
•Free technical support seven days a week,
PRODUCT ILLUSTRATIONS
Front Panel
The front panel of the Model RO318 Cable/DSL Security Router contains LEDs that provide diagnostic and connectivity information.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Power LED |
|
|
|
|
|
|
|
| Link/Activity LED | ||||
|
|
|
|
|
|
|
| ||||||
| Test LED |
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
LEDs
You can use some of the LEDs to verify connections. All LEDs are green when lit with the exception of TEST, which is amber.
Label | Activity | Description |
POWER | On | Power is supplied to the router. |
|
|
|
TEST | On | A fault has been detected. |
| Blinking | The system is initializing. |
| Off | The system is ready and running. |
|
|
|
Internet (WAN) |
|
|
LINK | On | The Internet port has detected a link with an attached device. |
ACT (Activity) | Blinking | Data is being transmitted or received by the Internet port. |
|
|
|
Local (LAN) |
|
|
100 | On | The Local port is operating at 100 Mbps. |
| Off | The Local port is operating at 10 Mbps. |
LNK/ACT | On | The Local port had detected a link with an attached device. |
| Blinking | Data is being transmitted or received by the Local port. |
|
|
|
Rear Panel
The rear panel of the RO318 Cable/DSL Security Router is shown below. You can refer to this diagram to identify the router ports before you attempt to make any connections.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Ground |
|
|
|
|
|
|
|
|
|
|
|
|
|
| 12 V DC power adapter outlet | ||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
TROUBLESHOOTING
Symptom | Cause | Solu | tion |
PWR and other LEDs | No power is received | Make sure the power cord is properly connected to | |
are not lit when you | to the router | the router. | |
switch on your router |
|
| Make sure you are using the correct NETGEAR power |
|
|
| |
|
|
| adapter supplied with your router. |
|
|
| Make sure the power adapter is properly connected to |
|
|
| a functioning power outlet. |
|
|
| After you apply power to the router, the TEST LED |
|
|
| should turn off after approximately 90 seconds. |
|
|
| If the TEST LED does not turn off, switch off the |
|
|
| router; then switch it on again. |
|
|
| |
LOCAL or INTERNET | Hardware connection | Make sure the Ethernet cable connections are secure at | |
LINK/ACT LEDs do not | problem |
| the router and at the device to which you are connected. |
light when connected to |
|
| Make sure the connected device is powered on. |
your PCs or modem |
|
| Be sure you are using the correct cable: |
|
|
| • If you are connecting one of the router's LAN |
|
|
| ports to a PC, use a standard |
|
|
| Ethernet cable like the one provided with your router. |
|
|
| • When connecting the router’s Internet port to a |
|
|
| cable or DSL modem, use the cable supplied with |
|
|
| your modem, not the one supplied with your router. |
|
|
| |
Router is unable to | Your PC may not | A DNS server is a host on the Internet that translates | |
load any Web pages | recognize any DNS | Internet names (such as WWW addresses) to numeric IP | |
from the Internet | server addresses | addresses. Typically your ISP will provide the addresses | |
|
|
| of one or two DNS servers for your use. If you entered a |
|
|
| DNS address into your router during the configuration, |
|
|
| reboot your PC and verify the DNS address as described |
|
|
| in “Verifying TCP/IP Properties.” Alternatively, you may |
|
|
| manually configure your PC with DNS addresses as |
|
|
| explained in “Configuring TCP/IP” in the Reference |
|
|
| Guide for the Model RP114 Cable/DSLWeb Safe Router. |
| Your PC may not have | If your PC obtains its information from the router by | |
| the router configured | DHCP, reboot the PC and verify the gateway address as | |
| as its TCP/IP gateway | described below in “Verifying TCP/IP Properties.” | |
| Your router may have | Verify that the router has a WAN IP address by follow- | |
| been unable to obtain | ing these steps: | |
| a WAN IP address | 1. Launch a browser and selct an external site. | |
| from the ISP | 2. Return to the Main Menu of the router’s | |
|
|
| |
|
|
| configuration (http://192.168.0.1). |
|
|
| 3. Under the Advanced heading, click on Maintenance. |
|
|
| 4. Check that an IP address is shown for the WAN |
|
|
| Port. If 0.0.0.0 is shown, reconfirm the configuration |
|
|
| information from your ISP. |
|
|
|
|
Verifying TCP/IP Properties (Windows)
After the Windows PC is configured and has rebooted, you can check the TCP/IP configuration using the Windows utility winipcfg.exe (for Windows NT systems, use ipconfig.exe).
To check your PC’s TCP/IP configuration:
1.On the Windows taskbar, click the Start button, and then click Run. The Run window opens.
2.Type winipcfg, and then click OK. The IP Configuration window opens.
3.Select your Ethernet adapter. The window is updated to show your settings, which should match the values below if you are using the default TCP/IP settings that NETGEAR recommends:
•The IP Address is between 192.168.0.2 and 192.168.0.32
•The Subnet Mask is 255.255.255.0
•The Default Gateway is 192.168.0.1
4.Click More Info, and verify that the “DNS Servers” box displays 192.168.0.1.
Verifying TCP/IP Properties (Macintosh)
After the Macintosh has rebooted, check the TCP/IP properties:
1.From the Apple menu, select the TCP/IP Control Panel.
2.If you are using the default TCP/IP settings that NETGEAR recommends, your setting should match these:
•The IP Address is between 192.168.0.2 and 192.168.0.32
•The Subnet Mask is 255.255.255.0
•The Router address is 192.168.0.1
•Name server address is 192.168.0.1
© 2001 by NETGEAR, Inc. All rights reserved.
Trademarks
NETGEAR is a trademark of NETGEAR, Inc. Other brand and product names are trademarks or registered trademarks of their respective holders. Information is subject to change without notice.
Statement of Conditions
In the interest of improving internal design, operational function, and/or reliability, NETGEAR reserves the right to make changes to the products described in this document without notice.
NETGEAR does not assume any liability that may occur due to the use or application of the product(s) or circuit layout(s) described herein.
Certificate of the Manufacturer/Importer
It is hereby certified that the NETGEAR Model RO318 Cable/DSL Security Router has been suppressed in accordance with the conditions set out in the
Federal Office for Telecommunications Approvals has been notified of the placing of this equipment on the market and has been granted the right to test the series for compliance with the regulations.
Bestätigung des Herstellers/Importeurs
Es wird hiermit bestätigt, daß das Model RO318 Cable/DSL Security Router gemäß der im
Das Bundesamt für Zulassungen in der Telekommunikation wurde davon unterrichtet, daß dieses Gerät auf den Markt gebracht wurde und es ist berechtigt, die Serie auf die Erfüllung der Vorschriften hin
zu überprüfen.
Voluntary Control Council for Interference (VCCI) Statement
This equipment is in the second category (information equipment to be used in residential areas) and con- forms to the standards set by the Voluntary Control Council for Interference by Data Processing Equipment and Electronic Office Machines that are aimed at preventing radio interference in residential areas.
EN 55 022 Declaration of Conformance
This is to certify that the NETGEAR Model RO318 Cable/DSL Security Router is shielded against the generation of radio interference in accordance with the application of Council Directive 89/336/EEC, Article 4a. Conformity is declared by the application of EN 55 022 Class B (CISPR 22).
Federal Communications Commission (FCC) Compliance Notice: Radio Frequency Notice
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
Canadian Department of Communications Radio Interference Regulations
This digital apparatus (NETGEAR Model RO318 Cable/DSL Security Router) does not exceed the Class
B limits for
Règlement sur le brouillage radioélectrique du ministère des Communications
Cet appareil numérique (NETGEAR Model RO318 Cable/DSL Security Router) respecte les
limites de bruits radioélectriques visant les appareils numériques de classe B prescrites dans le Règlement sur le brouillage radioélectrique du ministère des Communications du Canada.
Local Ethernet Ports | Internet port |