NETGEAR manual First, Set Up the WAG302, Deploy the WAG302, Now, Verify Wireless Connectivity

)NSTALLATION 'UIDE

WAG302 ProSafe Dual Band Wireless Access Point

Start Here

Please refer to the Reference Manual on your Resource CD for instructions on advanced configuration options.

Estimated Completion Time: 30 minutes.

Tip: Before mounting the WAG302 in a high location, first set up and test the WAG302 to verify wireless network connectivity.

First, Set Up the WAG302

1.Connect the wireless access point to your computer and modem

e.Turn on your computer, connect the power adapter to the WAG302 and verify the following:

•Power: The power light should be lit. If the power light is not lit, check the connections and check to see if the power outlet is controlled by a wall switch that is turned off.

•Test: The test light blinks when the WAG302 is first turned on.

•LAN: The LAN light on the WAG302 should be lit (amber for a 10 Mbps connection and green for a 100 Mbps connection). If not, make sure the Ethernet cable is securely attached at both ends.

•Wireless: The WLAN lights (e.g., 802.11a and 802.11g) should be lit.

2.Configure LAN and Wireless Access

a.Configure the WAG302 Ethernet port for LAN access.

•Connect to the WAG302 by opening your browser and entering http://192.168.0.230 in the address field.

http://192.168.0.230

Deploy the WAG302

1.Disconnect the WAG302 and position it where you will deploy it. The best location is elevated, such as wall mounted or on the top of a cubicle, at the center of your wireless coverage area, and within line of sight of all the mobile devices.

2.Position the antenna. Vertical positioning provides best side-to-side coverage. Horizontal positioning provides best top-to-bottom coverage.

3.Connect an Ethernet cable from your WAG302 Access Point to a LAN port on your router, switch, or hub.

4.Connect the power adapter to the wireless access point and plug the power adapter in to a power outlet. The PWR, LAN, and Wireless LAN lights should light up.

Tip: The WAG302 supports Power Over Ethernet (PoE). If you have a switch that provides PoE, you will not need to use the power adapter to power the WAG302. This can be especially convenient when the WAG302 is installed in a high location far away from a power outlet.

Now, Verify Wireless Connectivity

a.	Unpack the box and verify the contents.
b.	Prepare a PC with an Ethernet
	adapter. If this PC is already part	A
	of your network, record its
	TCP/IP configuration settings.
	Configure the PC with a static IP
	address of 192.168.0.36 and
	255.255.255.0 as the subnet mask.
c.	Connect an Ethernet cable from
	the WAG302 to the PC (point A in
	the illustration).	Computer

d.Securely insert the other end of the cable into the WAG302 Ethernet port (point B in the illustration).

Blue NETGEAR

Cable

B

4

WAG302 Ethernet

Port

•When prompted, enter admin for the user name and password for the password, both in lower case letters.

•Click the Basic Settings link and configure the IP Settings for your network.

b.Configure the wireless interface for wireless access. See the online help or the Reference Manual for full instructions.

c.Test wireless connectivity using a PC with a wireless adapter configured according to the wireless settings you just set in the WAG302 to establish a wireless connection to the WAG302.

Now that you have finished the setup steps, you are ready to deploy the WAG302 in your network. If needed, you can now reconfigure the PC you used in step 1 back to its original TCP/IP settings.

Using a computer with an 802.11a/g wireless adapter, verify connectivity by using a browser such as Netscape® or Internet Explorer to connect to the Internet, or check for file and printer access on your network.

Note: If you cannot connect, see to Troubleshooting Tips in this guide or the Reference Manual on the Resource CD for ProSafe Wireless Access Point.