Supported

2.400 ~ 2.4835GHz (Global), 5.18 ~ 5.32 GHz, 5.745 ~ 5.825 GHz, channels

Frequency Bands

country specific

 

 

Supported

802.11b—US, Canada, Taiwan 11; ETSI up to 13; Japan 14

Operating

802.11g—US, Canada, Taiwan 11; ETSI up to 13; Japan 13

Channels

802.11a—US, Canada, Taiwan 13; ETSI up to 19; Japan 8

 

 

Output transmit

100 mW maximum (or lower as configured on the WFS709TP ProSafe Smart

power

Wireless Switch to comply with local regulatory requirements)

 

 

Radio band

Via WFS709TP ProSafe Smart Wireless Switch in software manageability:

selection

• Management of all 802.11 parameters

 

• Network wide AP management via WEB GUI and SNMPv3

 

• Access Point Profiles, managed by geographical location, BSSID and radio

 

type

 

 

Encryption

40bit / 64bit / 128bit / 152bit WEP, TKIP, AES

 

 

802.11b and g

• 802.11b mode at 1Mbps: -95 dBm; 802.11b mode at 2 Mbps: -93 dBm;

Typical Receive

802.11b mode at 5.5 Mbps: -91dBm; 802.11b mode at 11 Mbps: -89 dBm;

Sensitivity

• 802.11g mode at 6 Mbps: -91 dBm; 802.11g mode at 9 Mbps: -90 dBm;

 

802.11g mode at 12 Mbps: -89 dBm; 802.11g mode at 18 Mbps: -87 dBm;

 

802.11g mode at 24 Mbps: -84 dBm 802.11g mode at 36 Mbps: -81 dBm;

 

802.11g mode at 48 Mbps: -77 dBm; 802.11g mode at 54 Mbps: -75 dBm;

 

802.11g mode at 108 Mbps: -72 dBm

 

 

Compliance

Access Points are radio transmission devices and as such are subject to governmental regulation. Network administrators responsible for the configuration and operation of Access Points must comply with local transmis- sion regulations. Specifically, Access Points must use channel assignments appropriate to the location in which the Access Point will be used.

WAGL102 or WGL102 Light Wireless Access Points are intended only for installation in Environment A as defined in IEEE 802.3af, Power over Ethernet. All interconnected equipment must be contained within the same building, including the interconnected equipment’s associated LAN connections.

When installed in an air-handling space, such as above suspended ceiling (plenum), the unit is required to be powered via PoE only. Additional cabling such as Fast Ethernet (FE) cables installed in such spaces should be suitable under NEC Article 800.50 and marked accordingly for use in plenums and air-handling spaces with regard to smoke propagation, such as CL2-P, CL3-P, MPP or CMP.

FCC

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate

May 2, 2007

radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harm- ful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at their own expense. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.

This product complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, includ- ing interference that may cause undesired operation.

RF Radiation Exposure Statement

This equipment complies with FCC RF radiation exposure limits. This equipment should be installed and oper- ated with a minimum distance of 20cm (7.9 inches) between the radiator and your body for 2.4 GHz and 5 GHz operations. This transmitter must not be co-located or operating in conjunction with any other antenna or trans- mitter.

This device when operated in the 5.15 to 5.25 GHz frequency range is restricted to indoor use to reduce the potential for harmful interference to co-channel Mobile Satellite Systems.

Europe

Warning-This is a Class B product. In a domestic environment, this product may cause radio interference in which case the user may be required to take adequate measures.

This product complies with 1999/5/EC, EN5022 Class B, and EN5024 standards.

Certifications

Electromagnetic Compatibility

IEC 60950 CB certificate and report

FCC DOC Part 15 Class B (digital portion)

FCC Part 15 Subpart C 15.247

FCC Part 15 Subpart E 15.407

RSS 210 (Canada)

CE marked with NB letter of opinion

EN 300 328 2.4 GHz

EN 301 893 5.4 GHz

AS/NZS 3548 Class B

AS/NZS4771 (C-tick)

Safety Compliance: IEC 60950; EN 60950

Plenum Use: Suitable for use in environmental air handling space in accordance with Section 300.22.C of the National Electrical Code, and Sections 2-128, 12-010(3) and 12-100 of the Canadian Electrical Code, Part 1, C22.1

Medical: EN 60601-1-1: 2001; EN 60601-1-2: 2001

Technical Support

Thank you for selecting NETGEAR products.

After completing installation, locate the serial number on the bottom label of the Light Wireless Access Point and use it to register your product at http://www.netgear.com/register.

Registration on the web site or over the phone is required before you can use our telephone support service. The phone numbers for worldwide regional customer support centers are on the Warranty and Support Information card that came with your product.

Go to http://www.netgear.com/support for product updates and web support.

This symbol was placed in accordance with the European Union Directive 2002/96 on the Waste Electrical and Electronic Equipment (the WEEE Directive). If disposed of within the European Union, this product should be treated and recycled in accordance with the laws of your jurisdiction implementing the WEEE Directive.

© 2007 by NETGEAR, Inc. All rights reserved. NETGEAR and the NETGEAR logo are registered trademarks of NETGEAR, Inc. in the United States and/or other countries. Other brand and product names are trademarks or registered trademarks of their respective holders. Information is subject to change without notice.

Page 2
Image 2
NETGEAR WGL102-100NAS, WAGL102-100NAS, GS116E-100NAS specifications Compliance, Certifications, Technical Support

WGL102, GS116E-100NAS, WGL102-100NAS, WAGL102, WAGL102-100NAS specifications

The NETGEAR WAGL102-100NAS, WAGL102, WGL102-100NAS, and GS116E-100NAS are leading products in the realm of home networking and connectivity solutions. These devices are engineered to enhance the performance of small to medium-sized networks, providing seamless connectivity and advanced features to meet the demands of modern digital environments.

The WAGL102 series, specifically the WAGL102-100NAS and WGL102-100NAS, are Wireless Access Points designed to extend wireless network coverage and improve connectivity throughout a home or office space. They operate on dual-band frequencies, supporting both 2.4 GHz and 5 GHz bands, allowing users to experience faster wireless speeds and reduced interference. Equipped with advanced technology such as Wi-Fi 6 (802.11ax), these access points can handle multiple devices simultaneously, making them ideal for environments with numerous connected gadgets. The seamless roaming feature ensures that devices can switch between access points without any interruption, providing a consistently reliable connection.

For businesses and advanced users, the GS116E-100NAS is a Managed Gigabit Ethernet Switch that provides 16 ports for wired connections. Its key features include VLAN support, QoS (Quality of Service) for prioritizing traffic, and IGMP Snooping for efficient multicast data handling. This switch is designed for high-performance networking, supporting advanced configurations that allow IT administrators to manage and optimize their networks effectively. Additionally, its energy-efficient design reduces power consumption, which is essential for sustainability-conscious organizations.

All these NETGEAR products are built with user-friendly interfaces, enabling easy setup and management. Many models come with NETGEARā€™s Smart Control Center, allowing users to monitor and manage their network from a single dashboard. Moreover, security features like WPA3 encryption, along with guest networking options, ensure that users can maintain a secure and protected network environment.

In summary, the NETGEAR WAGL102 series and GS116E-100NAS are prime examples of cutting-edge networking technology. They cater to the needs of both home users and businesses, ensuring robust connectivity, advanced management features, and security. With these devices, NETGEAR continues to deliver high-quality networking solutions adept at handling the increasingly connected world.