Merger Attachment Specifications, Side Deflector

New Holland SP Windrower Dual Windrow

Merger Attachment Specifications

GENERAL INFORMATION
Mechanical design	Laterally-mounted, draper-belt conveyor; folds up under windrower belly frame when not in use, allowing single windrow or swath formation.
		Merger folds down and forward (further forward at the left end) when deployed for merging application.
		Movable deflector allows operator to control distance crop is thrown.
Crop delivery direction		Right side, behind right front tire
Windrower compatibility		Tier II, 6-cylinder models (non-draper) and all Tier III, 6-cylinder models (except with dealer-installed draper ready)
Windrower software requirement		7.1 or higher*
Header compatibility		15.5' and 18' disc headers with conditioning system
Belt construction		Single ply w/two ply edges; vulcanized endless construction w/vee-guide tracking rib on inner surface and lateral
		cleats on the outer surface to positively move material
Belt tensioning		Adjustable spring tension to minimized shock loading
Belt tracking		Eye bolt adjustment at front end of driver roll
Merger conveyor flotation		Table can float upward to minimize damage in the event of an obstruction or obstacle
HYDRAULIC SYSTEM
Raise/lower-deflector- belt drive		Common system utilizing optional windrower-mounted auxiliary hydraulic system
Pump type		Windrower-mounted,fixed-displacement
Pump capacity @ rated speed, gpm		Tier II - 11.3 gpm (42.8 lpm); Tier III - 15.1 gpm (57.2 lpm)
Relief Pressure, psi (bar)		2000 (137.9)
Belt drive type		Fixed-displacement gear motor drive through #50 chain
Motor displacement, cu. in. (cu. cm)		1.53 (25)
Conveyor belt speed range, mph (kph)		7 - 13 (11.3 - 21)
Raise/lower cylinder, in. (mm)		2.5 (63.5) diameter,double-acting w/mechanical transport lock
Side deflector cylinder, in. (mm)		1.5 (38.1) diameter, double-acting
SIDE DEFLECTOR
Design	Top-hinged,formed steeldeflector w/plasticlowerextensionto protectthe deflector fromdamage in the eventof hitting an obstructionor high-centering
Mounting frame	Horizontal (manually) adjustable to accommodate two sizes of headers and operator preference on windrow shape and width
OPERATOR CONTROLS
Raise/lower		Propulsion handle-mounted button control- fully up or fully down
Belt speed		Right-hand console mounted, two-action On/Off switch and variable speed toggle switch
Side deflector		Propulsion handle-mounted rocker-switch, variable position control
DIMENSIONS
Conveyor frame length, in. (mm)		77.4 (1966.2)
Conveyor frame width, in. (mm)		89 (2260.5)
Conveyor belt width, in. (mm)		42 (1066.8)
Conveyor belt length, in. (mm)		84.6 (2150) center to center of rolls
Belt roller diameter, in. (mm)		4 (101.6)
Ground clearance, operating, in. (mm)		Adjustable; 5 (127) recommended (continuous ground contact is not intended)
Ground clearance, transport, in. (mm)		28 (711)
WEIGHT (merger attachment only; does not include aux. hyd. kit)
Shipping, lb. (kg)		1125 (510.3)
Operating, lb. (kg)		976 (443)
LUBRICATION
Grease points		50 hr. lube interval at 3 zerks
Drive chain		10 hr or daily interval; lube belt drive chain w/motor oil
OTHER REQUIREMENTS
Auxiliary hydraulic drive kit		Select Tier II (dealer installed) or Tier III kit (factory- or dealer-installed option)

*7.1 is assumed to be the level that will be installed concurrent w/MY09 Job 1 at this time (3/08). MY08 units have 7.0 installed. Special software was provided for each of the pre-build units. Software on those units need not be replaced, unless other issues would necessitate it.

Visit our Web site at www.newholland.com/na Or, call toll-free: 1-888-290-7377

Design, materials and/or specifications are subject to change without notic e and withou t liability therefor. Specifications are applicable to units sold in Canada, the United States, its territories and possessions, and may vary outside these areas.

Safety begins with a thorough understanding of the equipment. Always make sure you and your operators read the Operator’s Manual

before using the equipment. Pay close attention to all safety and operating decals and never operate machinery