Niles Audio CM950SUB series dimensions Installation Considerations

• Install subwoofer into frame after the paint is dry

• Install grille after paint is dry

Figure 3. Installing the subwoofer

• Rubber gloves and protective eyewear

• Keyhole or drywall saw

• Phillips screwdriver set

• Wire stripper

• Stud finder

• Cable ties

• Pencil

INSTALLATION CONSIDERATIONS

We recommend using the following tools and material to install your Niles CM900 series subwoofer:

• A minimum of two runs of 16-gauge two conductor subwoofer wire or one run of the same size four conductor subwoofer wire

• Electric drill with 1/4 – and 1⁄2-inch drill bits and a 1-inch flat drill bit

(for drilling through studs)

• Stiff wire, fish tape or glow rods for routing cables

Before starting the installation, please observe the following precautions:

•Turn off all system power before making any connections

•Always wear protective eyewear when using tools

•Make sure hands are clean before installation

•Wear gloves when working with fiberglass insulation

RUNNING WIRES IN WALLS OR CEILINGS

When running subwoofer wire inside walls or ceilings, use special jacketed cable (CL-2 or CL-3) to protect the wire and for fire prevention. In some areas, conduit is also required. For a trouble-free installation, low-voltage wire such as subwoofer wire must be run in accordance with the National Electrical Code and any applicable provisions of the local building code. If you are unsure of the correct installation techniques, wire jacket, or type of conduit to use, consult a professional audio/video installer, building contractor, or the local building and inspection department.

SELECTING THE NUMBER AND LOCATION FOR YOUR SUBWOOFER

The CM900 series passive subwoofers are designed to be installed in any standard ceiling. There are two considerations for placing the subwoofer; ease of running the cable to the desired location and the effect that placement may have on performance. Installing the subwoofer in a corner position will enhance the perceived bass output to some listeners, but may also produce a “boomy” sound.

INSTALLING WITH SATELLITE SUBWOOFER

A concealed CM900 series subwoofer installation allows you to enjoy your entertainment system with full range sound even if your satellite subwoofers are small. When used with satellite subwoofers that have substantial bass of their own, the CM900 series subwoofer will augment the bass performance. A typical installation is illustrated below. It is possible to control the volume of the sound of both the subwoofer and the satellite subwoofers simultaneously. The volume control is connected in-line with the subwoofer. An example of wiring an area that has 1 subwoofer and 2 loudspeakers installed with a master volume control is shown in Figure 1. In addition to controlling the volume of the subwoofers, these controls allow the addition of added loudspeakers without adding more amplifier channels. Niles manufactures a wide variety of volume controls and other accessories that can suit virtually any of your needs.

LOWPASS
100Hz	140Hz

INSTALLATION

1.The CM900 series subwoofers feature a separate frame assembly which installs with four clamps or mounting “dogs” which hold the frame in place. The dogs are tightened via four front-baffle screws. Tighten the dogs by turning the screws clockwise. DO NOT OVER- TIGHTEN THESE SCREWS. Over-tightening the clamps may make the grille difficult to install.

NOTE: THE SCREWS WILL TURN EASIER IF YOU “PRIME” THEM FIRST. BEFORE INSTALLING EACH SUBWOOFER, TURN THE SCREWS IN AND THEN TURN THEM BACK OUT TO THEIR ORIGINAL POSITIONS.

2.At each subwoofer location, route the wire through the installed frame, then separate the subwoofer wire so that at least 2 inches of each conductor are free. Strip away 1/4 inch of insulation from each subwoofer wire.

3.On each set of subwoofer connectors, press down the spring-loaded connector, insert the appropriate conductor, and then release the connector. Gently tug on the subwoofer wire to make sure it is held in place. If not, repeat this procedure until it is. (See Figure 2).

NOTE: OBSERVE CORRECT POLARITY: POSITIVE (+) GOES TO THE RED POST AND NEGATIVE (–) GOES TO THE BLACK POST.

4.Holding the subwoofer in the palm of your hand, insert it into the frame and twist clockwise using the two molded tabs. This will lock it into the frame. (See Figure 3).

5.Connect the other end of each subwoofer wire to the receiver (or amplifier) in the same way.

6.Adjust high pass and low pass crossover switches if desired.

7.Install grille. The flush-mount MicroPerfTM metal grilles can be painted to blend with the surrounding decor.

8.Remove cardboard paint mask / template from the box and keep for future potential use.

9.Turn on the receiver or amplifier and test all subwoofers in the system.

IMPORTANT: DO NOT OVER TIGHTEN THE SCREWS! OVER TIGHTENING THEM MAY MAKE THE GRILLE DIFFICULT TO INSTALL

PAINTING THE GRILLE AND FRAME

Each CM900 series subwoofer frame and flush-mount metal grille may be painted without the need for primer. For best results when painting the grille, use a spray gun or airless sprayer, thin the paint to prevent clogging of the grille holes, and apply several light coats instead of one heavy one.

• Install subwoofer frame into ceiling or wall

• Paint the frame of the subwoofer

•Paint the grille separately from the subwoofer frame

Figure 1. 1 Subwoofer and 2 satellite loudspeaker using one	Figure 2. Subwoofer connectors
master volume control