INSTALLATION CONSIDERATIONS
CHANGING THE COLOR
OF THE KNOB AND THE
DECORA INSERT
The
1.Obtain the appropriate knob and Decora- style insert in the desired color from your Niles dealer.
2.Pull the knob off the shaft. See Figure 1.
3.Locate the two plastic mounting tabs at the top rear of the
4.Locate the new
5.Locate the new knob. Align its flat side to the flat side of the shaft, and push the knob onto the shaft. Check the alignment of the knob by turning it through all positions.
Figure 1. Changing the VCS50’s knob and
INSTALLATION
If you are installing the VCS50 into an existing wall, take time to consider any possible obstructions which may be hidden inside the wall, such as wood and metal studs; electrical, telephone or other types of wiring; plumbing; conduit; old wall safes; etc.
1.Install the junction box in the usual manner.
2.Run all the necessary wiring to the VCS50. Label the wires for future reference.
3.Make the connections to the VCS50. Locate the connectors for the VCS50. Strip 1/4" of insulation from the end of each wire. Tightly twist the end of each wire until there are no frayed ends. Insert each wire into the appropriate hole on the connector blocks;
secure the wiring to the connectors by tight- ening the small connector screws. Be certain that proper phasing is observed— connect the positive terminals on the VCS50 to the positive terminals on the amplifier and speakers; the negative terminals on the VCS50 to the negative terminals on the amplifier and speakers. See Figures 2 and 3.
NOTE: THE INPUTS OF THE VCS50 ARE THE CONNECTOR PINS LABELED “IN”. THE OUTPUTS ARE THE CONNECTOR PINS LABELED “OUT”. BE SURE NOT TO REVERSE THESE CONNECTIONS OR THE VCS50 WILL NOT FUNCTION PROPERLY.
4.Secure the VCS50 to the junction box. Insert the
5.Use the shorter plate screws to fasten the
Decora faceplate to the VCS50. DO NOT OVER-
TIGHTEN THE PLATE SCREWS OR YOU MAY DAM- AGE THE FACEPLATE. Line up all the screws in the same direction for a finished look.
Figure 2. |
Wiring the connectors |
|
|
| OPERATION | |
| Receiver |
| 1. | Make sure the amplifier or receiver power is |
|
|
| ||
|
|
|
| OFF and set the volume to minimum. |
|
|
| 2. | Set the VCS50 volume to maximum |
Left | VCS50 | Right |
| (fully clockwise). |
|
| |||
(Input) |
| (Input) | 3. | If you are using a Niles speaker selection |
|
|
| ||
|
|
|
| system, locate the on/off button which |
|
|
|
| corresponds to the speaker pair you wish to |
|
|
|
| play. Set it to the on position. |
To Speakers |
| 4. | Turn on the amplifier or receiver and select a | |
|
| source, such as the tuner or CD player. | ||
(Output) |
|
|
|
|
| 5. Slowly turn up the amplifier or receiver volume |
| Figure 3. Wiring | and set it to a comfortable (not maximum) |
| diagram shows a Niles | listening level. Be careful not to overdrive or |
| system with a VCS50 | “clip” your amplifier. If the sound becomes |
Speakers | volume control | |
|
| muddy or distorted, you have reached the limit |
|
| of your amplifier’s volume capability and should |
|
| quickly reduce the volume to avoid damaging |
|
| your speakers. |
|
| 6. Adjust the volume of the speakers to the |
|
| desired listening level using the VCS50. If all |
|
| the speaker pairs in your system are equipped |
|
| with Niles volume controls, you can leave the |
|
| amplifier or receiver volume set at one position |
|
| and use the Niles controls exclusively. |
| Figure 4. Loosening | 7. You can turn off the speakers by turning the |
| knob on the VCS50 fully | |
| the screws for a flush fit. | |
|
| or by pressing the on/off button on your |
|
| speaker selector. |
1
2 | 3 |
4
5 | 6 |