Norcold 9162, 9163, 9182, 9183 manual When, IT Means, You Need to Check

Models: 9183 9182 9163 9162

1 15
Download 15 pages 33.09 Kb
Page 8
Image 8
When :

DiagnosticsAbout Your RefrigeratorIT Means:You Need to Check:Manual background

Manual Mode

Press and hold MODE until the AUTO LED goes out and the desired operating mode lights. Unlike AUTO mode, the operating mode LED stays lit until an alternate mode is selected. If the energy source is interrupted in MANUAL mode, the corresponding LED flashes, and the refrigerator stops operating until an alternate energy source is selected or the problem is corrected. See Diagnostics for corrective actions.

AUTO and MANUAL Modes - Gas Operation Only

If gas does not ignite within 30 seconds, the refrigerator’s gas valve automatically closes and the operating controls select an alternate energy source (AUTO Mode) or revert to a stand-by mode where the LP GAS LED flashes. The LED flashes until the refrigerator is turned OFF and then ON. If gas does not ignite after several attempts, check input gas supply, or consult your dealer or a Norcold authorized service center. Select a different operating mode by pressing and holding MODE. The refrigerator does not switch to the new operating mode until you release MODE.

Backup Operating System (BOS)

This refrigerator has a Back-Up Operating System to allow the refrigerator to cool in case of a failure within the temperature sensing circuit. If this happens, the TEMP SET LED flashes and refrigerator switches to BOS mode. This mode provides cooling until the refrigerator is serviced. Check refrigerator temperatures when operating in this mode. If the temperature is too cold, adjust the thermostat to the left in single LED steps. If the temperature is too warm, adjust the thermostat to the right in single LED steps. Allow the refrigerator to operate at the new setting for one hour before rechecking the temperatures (frequent door opening prevents the temperatures from stabilizing). While the refrigerator can operate in this mode, Norcold recommends that you seek service as soon as practical to restore normal operation.

Diagnostics

When :

IT Means:

You Need to Check:

 

 

 

 

 

 

No LED"s light

Control voltage is unavailable to

10.5 to 15.4 VDC supplied to refrigerator.

 

display panel

Battery charging equipment or converter.

 

DC connection to the refrigerator.

 

 

 

 

Refrigerator’s DC fuse (3 Amp - Control Fuse)

 

 

See your dealer or a Norcold Service Center

 

 

 

Flashing LP GAS LED

LP gas ignition fault

10.5 to 15.4 VDC supplied to refrigerator.

(flash, pause, flash, pause etc.)

(Initial start-up)

Have gas lines been purged?

LP tank valve on?

 

 

 

 

LP tanks empty?

 

 

LP supply pressure 11" water column.

 

 

Refrigerator’s manual shut-off valve open.

 

 

See your dealer or a Norcold Service Center

Flashing AC LED

Fault external to refrigerator

Is refrigerator plugged into a functional AC outlet? Has

(flash, pause, flash, pause, etc.)

controls

the vehicle fuse or circuit breaker blown?

Vehicle generator functioning (if applicable).

 

AC Mode selected but AC

 

Refrigerator’s AC fuse (5 amp) blown?

 

power not available

See your dealer or a Norcold Service Center

 

 

 

Flashing AC LED

Fault external to refrigerator controls

AC input to refrigerator (108 VAC to 132 VAC)

(flash, flash, pause, flash, flash,

If AC problem cannot be located, see your

pause, etc.)

AC input voltage too low or too high

dealer, camp-ground administrator, or a Norcold

 

Service Center

 

 

 

Flashing BATTERY LED (flash,

 

Battery(s) Voltage

flash, pause, flash, flash, pause,

Fault external to refrigerator controls

Battery charging equipment or converter

etc.)

DC input voltage too high or too low

DC connection to the refrigerator

 

See your dealer or a Norcold Service Center

 

 

 

Flashing BATTERY LED

Fault within refrigerator controls

Not owner serviceable;

(flash, flash, flash, pause, flash,

 

See your dealer or a Norcold Service Center

flash, flash, pause, etc.)

 

 

 

 

 

Current TEMP SET LED flashing

Fault within refrigerator controls

Not owner serviceable;

(flash, pause, flash, pause, etc.)

Back-Up Operating System

Temporary operating mode; read Back-Up

 

Mode

Operating System. Seek service as soon as

 

practical.

 

 

 

 

See your dealer or a Norcold Service Center

 

 

 

 

 

 

8

Page 8
Image 8
Norcold 9162, 9163, 9182, 9183 manual When, IT Means, You Need to Check