3. Cut the rubber band holding the Upright Wire Harness

3

 

 

98

(98). Have a second person hold the console assembly

 

 

 

 

 

 

 

 

 

near the Uprights (69). Connect the Upright Wire Harness

 

 

81

 

to the wires extending from the Console Base (81). The

 

 

 

connectors should slide together easily and snap into

 

 

 

 

place. If they do not, turn one connector and try again.

 

 

 

 

Insert the connectors and the Upright Wire Harness into

 

98

 

 

the right Upright, and then set the console assembly on

 

 

 

 

the Uprights. Be careful not to pinch the wires.

 

 

 

 

 

 

 

69

 

 

Console

 

 

 

 

Assembly

 

 

 

4. Insert a Handrail (118) into the right side of the console

4

 

 

 

assembly as shown; you may need to twist the Handrail

 

 

 

 

 

 

 

as you insert it. Next, insert two 4 1/2” Bolts (78) with

 

 

 

 

Handrail Bushings (77) into the right Upright (69) and the

 

 

 

 

Handrail. Be careful not to pinch the wires. Make sure

 

 

 

 

that the Handrail Bushings are flush against the right

 

 

 

 

Upright, with the thicker sides facing the center of the

 

 

69

 

treadmill, as shown in the inset drawing.

 

 

Thick

 

 

77

 

 

 

Next, lift the console assembly and the Handrail (118)

 

 

 

Side

118

 

 

 

slightly and align the 4 1/2” Bolts (78) with the holes in the

 

 

 

 

 

 

 

Handrail. Thread the Bolts into the Upright (69) and the

 

 

 

 

Handrail until the heads of the Bolts are against the

 

77

78

 

Upright. Do not tighten the Bolts yet.

 

 

 

Console

 

 

 

 

 

 

Attach the other Handrail (not shown) in the same way.

 

Assembly

 

 

Note: There are no wires on the left side.

 

 

 

 

5. With the help of a second person, carefully tip the

5

 

 

 

Uprights (69) down to the position shown. Make sure that

 

 

 

 

 

 

99

the Extension Legs (102) remain in the Uprights.

 

 

 

 

 

 

 

Attach each Extension Leg (102) with two 1” Tek Screws

69

 

 

53

 

 

 

(47) and a Base Pad (99) as shown. (Note: Attach the

 

 

 

 

lower Screw [without the Base Pad] first.) Next, align the

 

 

 

99

lower ends of the Handrails (118) with the holes in the

 

 

 

 

 

 

47

base of the Uprights (69). Attach each Handrail with a 4”

 

99

 

 

 

 

Bolt (53) as shown. Note: The Bolts must be at an

 

 

102

99

angle that matches the angle of the Handrails as

 

53

 

 

 

 

shown in the inset drawing.

 

 

 

 

 

 

 

With the help of a second person, carefully tip the

118

99

 

 

47

 

 

Uprights (69) back to the vertical position. See step 4.

 

 

53

 

 

 

Tighten the four 4 1/2” Bolts (78).

102

 

 

99

 

 

 

 

 

 

Note: A replacement Base Pad (99) may be included. Use

 

 

118

 

the Base Pad to replace any Base Pad that becomes worn.

 

 

 

 

6.Make sure that all parts are properly tightened before you use the treadmill. Keep the included allen wrench in a secure place. The allen wrench is used to adjust the walking belt (see page 26). To protect the floor or carpet from damage, place a mat under the treadmill.

7

Page 7
Image 7
NordicTrack NTL10842 Uprights. Be careful not to pinch the wires, Handrail. Be careful not to pinch the wires. Make sure