MODEL:
| For help, call us toll |
| free! |
RECESSED |
Register your
INSTRUCTIONS
MODEL | WALL OPENING | OVERALL SIZE | ||||
NO. | W | H | D | W | H | D |
62BK244CBK(X) | 141/4 | 24 | 4 | 161/2 261/2 51/4 | ||
62BK244CCN(X) | 141/4 | 24 | 4 | 161/2 261/2 51/4 | ||
62BK244CCY(X) | 141/4 | 24 | 4 | 161/2 261/2 51/4 | ||
62BK244CMP | 141/4 | 24 | 4 | 161/2 261/2 51/4 | ||
62BK244TBK(X) | 141/4 | 24 | 4 | 161/2 261/2 51/4 | ||
62BK244TCY(X) | 141/4 | 24 | 4 | 161/2 | 261/2 | 51/4 |
62BK244TGK(X) | 141/4 | 24 | 4 | 161/2 | 261/2 | 51/4 |
62BK244TMP | 141/4 | 24 | 4 | 161/2 | 261/2 | 51/4 |
INSTALLATION
1. | Carefully remove all |
| packages, shelves and door aside |
| and shelves are located in the fi llers identifi ed by |
| Enclosed” tape. |
2. | Determine desired location of cabinet on wall. Mark wall to |
| show wall opening size (see dimension chart). Generally, the |
| recommended height to the center of the cabinet is 64” from |
| the fl oor. (Fig. 1) |
3. | CAUTION: Wall studs, plumbing or electrical lines that |
Fig. 1
Approx. 64" to Floor
D
W
H
Fig. 2
Insert screw through clear plastic base
interfere must be removed or relocated. Cut wall opening, |
being careful not to damage the surrounding wall surface. |
Insert framing to support all plaster board edges. |
4. Prepare the mounting screws by placing the screws into the |
plastic bases. (Fig. 2) |
5. Note: For ease of installation, an additional person is |
recommended. Insert cabinet into wall opening. (Fig.3) |
Ensure the cabinet is plumb and level. If necessary use a |
carpenter’s level and shim corners of cabinet. Secure to wall |
studs through the four (4) mounting holes inside cabinet, |
using the screws that have been placed into the plastic |
bases. (Fig. 4) Do not over tighten the mounting screws as |
the body side wall may bend and prevent proper shelf |
Fig. 3
Cabinet
Body
Wall Opening
Fig. 4
Mounting
Screws
Mounting screw into mounting hole
installation. Only tighten screws until they are fl ush with the |
body. |
6. Snap the screw covers over the screw bases. (Fig.5) |
INSTALLATION of DOORS
1.Remove hinges and screws from hardware bag. Mount hinge unit on door as shown in Fig. 6 securing with screws provided.
2.Install the door by inserting door side of the hinge into the bracket on the body shown in Fig. 7.
3.Check door for proper alignment. If the door needs to be adjusted please refer to the adjustment procedures in Fig. 8.
INSTALLATION of SHELVES, HOLE PLUGS AND BUMPERS
1.Select where you want the shelves to be placed.
2.Insert two (2) shelf brackets at each end of the shelf location. (Fig. 9).
3.Set shelves in place on the shelf brackets, pressing down on the shelf to lock in place. (Fig. 9).
4.Remove hole plugs from hardware bag and place in remaining holes. (Fig. 10).
5.Remove bumpers from hardware bag and position to body. (Refer to Service Parts Drawing - Key No. 9 for bumper locations).
Fig. 5 |
| Fig. 6 |
| |
|
| Hinge Mounted |
| |
Snap on Cover | Cover | to Door |
| |
|
|
| ||
Screw |
|
|
| |
| Base |
|
| |
Fig. 7 | Hook bottom of | Fig. 8 |
| |
| This screw for | |||
|
| |||
| hinge into place |
| ||
| Door Adjustment | up and down | ||
Hinge Mounted | on the bracket | |||
| adjustments | |||
|
| |||
to Cabinet |
|
|
| |
|
| This screw |
| |
|
| for depth |
| |
|
| adjustments |
| |
Press down |
| This screw |
| |
on hinge until it |
|
| ||
clips in place |
| for left and right | ||
|
| adjustments |
| |
Fig. 9 |
| Fig. 10 |
|