![](/images/new-backgrounds/1240479/24047913x1.webp)
OS35™ | |
and | www.omega.com |
| (203) |
Infrared Temperature Sensor
INSTALLATION INSTRUCTIONS
The following procedure is recommended:
1.Install the SmartIRt/c as close as practical to view the target material to be measured.
2.Wire the SmartIRt/c to the controller, PLC, etc. in standard fashion (see PIN- OUT and wiring diagram)
3.Bring the process up to normal operating temperature and measure the actual temperature of the target material with the Microscanner
4.Adjust "input offset," "zero," "low cal," on the readout device to match the
reading of your reference.
Installation Complete. (For OEM installations preset the same adjustments. Indi- vidual calibration is not required.)
1
3
5
4
2
WIRING DIAGRAM
|
| PIN OUT |
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
| Carol C074 Series/Belden 953 Series/Alpha 630 Series |
| |||||||
|
| Pin | Color |
| Function |
|
| Pin | Color |
| Function |
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
| 1 | White |
|
| Positive Output Signal |
| 6 | Brown |
| TA Pull Down Pin / IO option |
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
| 2 | Green |
|
| Reference Output Signal |
| 7 | Yellow |
| RS232_TXD / IO option |
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
| 3 | Red |
|
| Positive Power |
| 8 | Violet |
| RS232_RXD / IO option |
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 4 | Black |
|
|
| Ground |
| 9 | Blue |
| RS232_RTD (READY_TO_SEND) |
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 5 | Bare |
|
|
| Shield |
| 10 | Orange |
| RS232_CTS (CLEAR_TO_SEND) |
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
| ORDERING INFORMATION |
|
|
| ||||
|
|
|
| |||||||||||
| F | FIELD OF VIEW | P | POWER | O | OUTPUT | T | TEMPERATURE RANGE |
| |||||
| .3 | 3:1 |
| 12V | 12 VDC | 05 | 100C |
|
| |||||
.5 | 5:1 |
| 24V | 24 VDC | 010 | 250C |
| |||||||
.20 | 20:1 |
|
|
|
| 420 | 500C |
| ||||||
.40 | 40:1 |
|
|
|
| 232 | RS232 | 1000C |
| |||||
- | 1:2 |
|
|
|
|
|
|
| 70C |
| ||||
| .SV | 1:2 |
|
|
|
|
|
|
|
|
|
|
|
|
.4 | 4:1 |
|
|
|
|
|
|
|
|
|
|
|
| |
| .4SV | 4:1 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
OPTION: Add Ta to any part # to add ambient temperature option to output ambient temperature surrounding sensor
NOTE:
Examples: