OPERATING INSTRUCTIONS

OMEGA

Precautions

!Use filtered air. Avoid grease, oil, or oil vapors, corrosive or reactive gases which will damage heater.

!Use exposed junction type “K” thermocouple within one inch of the heater exit for good control.

Installation and Wiring

See attached drawings.

WARNING! Sensors are at or near line voltage. Use teflon jacketed, teflon insulated “K” thermocouple wire to connect heater sensors to the over-temperature board.

1.Be sure heater is securely mounted.

2.Follow all applicable electrical codes when mounting and wiring heater and control components.

Operation

1.Turn on air and set pressure or flow to desired operating level.

2.Turn on power to the over-temperature board.

3.Turn on power to the power controller.

4.Turn on power to the temperature controller.

5.Set desired temperature on temperature controller.

During operation, with steady-state airflow, the exit temperature should not vary more than a few degrees from set point. Although the heater will not burn out with zero airflow, if the heater is operated in a vertical downward position and an airflow of 100 SCFH or below is run through the heater, the inlet temperature of the heater will exceed 150°F and the Over-temperature board will begin to limit power to the heater.

To Shut Down:

1.Turn off power to the temperature controller and the power controller.

2.Allow air to continue to flow for a minimum of 1 minute or until exit air temperature is 150°C or less for safety. Continue airflow longer if hot equipment components present any potential hazard to personnel.

3.Turn off air to the system.

Replacing Elements

Before replacing the element assembly, determine the cause of the element failure. Prior to powering the system back up, make certain that the entire system is operating properly. Possible causes of element failure are:

1.Normal end of Life

2.Failure in Control System

3.Mechanical Damage to System

REPLACEMENT PROCEDURE

1.Turn off power to the system. Follow lock-out/tag-out procedures.

2.Unscrew the 3 external housing screws and remove the stainless heater housing.

3.Unplug element from its socket and plug new element into the socket.

4.Slide the stainless heater housing back over the element and secure housing with the 3 external housing screws.

Performance Curves

The following curves show the maximum temperature performance of the SH-Series heater as measured by a “K” type thermocouple located within 1” of heater exit. Use of other temperature measuring devices or varying the distance of the measurement may cause different temperature readings. The heaters will not generate temperatures greater than indicated on the graph in and if used correctly will maintain operating life in excess of 5000 hours.

P age 2

Page 1 Page 3
Page 2
Image 2
Omega Vehicle Security SH73343 Precautions, Installation and Wiring, Operation, Replacing Elements, Performance Curves
Page 1 Page 3

SH73343 specifications

The Omega Vehicle Security SH73343 is an advanced automotive security system designed to offer superior protection for your vehicle. With a slew of cutting-edge features, this security solution combines convenience with robust performance to safeguard your investment against theft and unauthorized access.

One of the standout features of the SH73343 is its two-way paging system, which allows vehicle owners to receive instant alerts on their remote key fob. This function ensures that users are always informed of their vehicle’s status, enhancing peace of mind. The LCD display on the key fob provides clear visual feedback regarding the system’s status, making it easy to check whether the vehicle is secure or if an alarm has been triggered.

Another key characteristic of the SH73343 is its advanced motion detection technology. The system employs sophisticated sensors that can detect both movement and forced entry. When an intrusion is detected, the alarm sounds, alerting the owner even from a distance. This proactive approach significantly reduces the risk of theft and increases the chances of recovering stolen vehicles.

Additionally, the Omega SH73343 features a programmable shock sensor, which allows users to customize the sensitivity level. This flexibility helps minimize false alarms from minor disturbances, while still providing effective protection against serious threats. Vehicle owners can adjust settings according to their personal preferences and the specific environment in which their car is parked.

The security system also includes an engine immobilizer feature that prevents the vehicle from being started without the correct key fob nearby. This adds an extra layer of security, as it not only alerts the owner to unauthorized access but also renders the vehicle inoperable to would-be thieves.

Moreover, the SH73343 is compatible with a variety of vehicles, ensuring that a wide range of car owners can benefit from its security technologies. The installation process is straightforward, and users can rely on the manufacturer's detailed guidance for a seamless setup.

In conclusion, the Omega Vehicle Security SH73343 is a comprehensive solution for any vehicle owner looking to enhance security. With its two-way paging system, advanced motion detection, customizable shock sensor, and engine immobilizer, this system is designed to deter theft effectively and provide maximum protection for your vehicle. Investing in the SH73343 means investing in peace of mind, knowing that your vehicle is well-guarded against potential threats.
Top Page Image Contents