FlexPointTM 10AUI/T User Instructions

Description:

The FlexPointTM 10AUI/T transceiver is an IEEE 802.3 compatible Ethernet unshielded twisted pair (UTP) trans- ceiver that provides physical medium connection to devices featuring Attachment Unit Interface (AUI) connectors. It can be powered from the AUI connector, an external AC or 48VDC power adapter or a 14-unit Powered Chassis.

The FlexPoint 10AUI/T has a 15-pin AUI connector that attaches to a mating AUI connector mounted on hosting Ethernet DTE equipment such as a workstation or a PC, or on a repeater such as a hub or a switch.

This FlexPoint 10AUI/T model is described here:

Model Maximum Distance

4321 100 meters

Operating in Half-Duplex, the FlexPoint 10AUI/T fea- tures a switch selectable SQE test function that pro- vides diagnostic information to the hosting station. It also provides LED status about network conditions that assist in network installation and maintenance.

The 4321 model can be used stand-alone, wall-mounted, rack-mounted on a 5-unit shelf or in a 14-unit AC or 48VDC Powered Chassis.

Power Adapter Notice:

1.When using in a stand-alone configuration, this product can be powered from the AUI port and does not require an external power source.

2.If the AUI port is not capable of providing power to the FlexPoint 10AUI/T and when using in a stand- alone configuration, this product is intended to be and must be used only with a Listed Direct Plug-In Power Unit marked “Class 2” and rated at 9Vdc, 1 Amp.

3.When using an external power source, this product should always be used only with Omnitron Supplied Power Unit model number 9113-PS.

WARNING!

Before inserting the Power Adapter, verify that the power on the unit is appropriate

for your AC line voltage source.

Mounting and Cable Attachment:

The FlexPoint 10AUI/T can be mounted using a wall- mounting kit. It can also be rack-mounted using a 5-Module shelf or a high-density 14-unit FlexPoint Powered Chassis.

Connect the FlexPoint 10AUI/T to the 15-pin AUI port on a PC, workstation, hub or switch; slide the connector latch locking it into place. The AUI cable is limited to 50 meters . Attach a UTP category 3 or higher cable to the RJ45 connector. Note that the total length of the cable should not exceed 100 meters.

Switch Settings:

“RJ45 Cross-Over” Switch: When connecting the UTP to a hub or switch, set switch to “Straight-Through” (factory setting). When connecting to a workstation, set it to “Cross- Over.”

“SQE” switch: When attaching to a PC (or a workstation), the SQE switch should be set to “SQE Enable” (factory setting). When connecting to a hub or a switch, it should be set to “SQE Disable.”

“UTP Range” switch: Set this switch according to the required distance of the UTP connection. For normal operation, set it to ”100m” (factory setting). When distance of over 100m is required, set it to “>100m”.

Note that when used in the “>100m” mode, the sensitivity of the FlexPoint 10AUI/T is increased making it more sensitive both to signal and noise, so this mode should be used with caution when the distance requires it.

LED Indicators:

LED

Color

Description

Power

Yellow

Power applied

AUI-Rx

Green

Host Data Received

UTP-Link/Rx

Green

UTP Link / Data Received

Collision/

 

 

Jabber

Yellow

Collision or Jabber Detected

Please complete both sides of this form

-Email:

Phone:Fax:

Country:

City:State: ZipCode:

______________________________________________

Address:

Company: ______________________________________________

Name: _________________________________________________

Omnitron Systems Technology, Inc. 140 Technology Drive, #500 Irvine, CA 92618, USA Fax: (949) 250-6514

andmailorfax

Pleaseregister

thisregistrationformto:

on-line@http://www.omnitron

 

-systems.comorcompletebothsides

User Warranty Registration

Warning

The operating description in this Instruction Manual is for use by qualified personnel only. To avoid electrical shock, do not perform any servicing of this unit other than that contained in the operating instructions, unless you are qualified and certified to do so by Omnitron Systems Technology, Inc.

Caution

All user-required operations can be performed without opening the unit. Never attempt to open or remove the cover or tamper with the unit.

Warranty

This product is warranted to the original purchaser against defects in material and workmanship for a period of TWO YEARS from the date of shipment. A LIFETIME warranty may be obtained by the original purchaser by REGISTERING this product with Omnitron within 90 days from the date of shipment. TO REGISTER, COMPLETEAND MAILOR FAX THE REGISTRATION PORTION OF THIS INSTRUCTION MANUAL TO THE INDICATED ADDRESS. Or you may register your product on the internet at http:// www.omnitron-systems.com. During the warranty period, Omnitron will, at its option, repair or replace a product which is proven to be defective.

For warranty service, the product must be sent to an Omnitron designated facility, at Buyer’s expense. Omnitron will pay the shipping charge to return the product to Buyer’s designated US address using Omnitron’s standard shipping method.

Limitation of Warranty

The foregoing warranty shall not apply to defects resulting from improper or inadequate use and/or maintenance of the equipment by Buyer, Buyer-supplied equipment, Buyer-supplied interfacing, unauthorized modifications or tampering with equipment (including removal of equipment cover by personnel not specifically authorized and certified by Omnitron), or misuse, or operating outside the environmental specification of the product (including but not limited to voltage, ambient temperature, radiation, unusual dust, etc.), or improper site preparation or maintenance.

No other warranty is expressed or implied. Omnitron specifically disclaims the implied warranties of merchantability and fitness for any particular purpose.

Exclusive Remedies

The remedies provided herein are the Buyer’s sole and exclusive remedies. Omnitron shall not be liable for any direct, indirect, special, incidental, or consequential damages, whether based on contract, tort, or any legal theory.

Form: 040-04321-001C 11/07

Technical Support:

For help with this product, contact our Tech. Support:

Phone:

(949) 250-6510

Fax:

(949) 250-6514

Address: Omnitron Systems Technology, Inc.

 

140 Technology Drive, #500

 

Irvine, CA 92618 USA

E-mail:

support@omnitron-systems.com

URL:

http://www.omnitron-systems.com

Please complete both sides of this

City:State: Zip Code: Country: Comments and Suggestions: ______________________________________________________ ______________________________________________________

form

 

Address: ______________________________________________

Purchased From: _________________________________________

Serial Number:Purchase Date:

Model:

FlexPoint Type:

and mail or fax

Please register

this registration form to:

on-line@ http://www.omnitron-systems.com

 

or complete both sides

User Warranty Registration

Page 1
Image 1
Omnitron Systems Technology warranty FlexPointTM 10AUI/T User Instructions, User Warranty Registration

10AUI/T specifications

Omnitron Systems Technology 10AUI/T is a critical device in the networking industry, designed to facilitate seamless communication in both legacy and modern networking environments. This versatile media converter functions as a bridge between 10BASE-T Ethernet and 10BASE-2 coaxial cable, making it an ideal solution for organizations aiming to maintain and extend their existing network infrastructure without incurring significant costs.

One of the standout features of the 10AUI/T is its robust compatibility, which supports both twisted pair cabling and coaxial connections. This flexibility allows businesses to easily integrate the converter into various network topologies, providing a smooth transition from older technologies to more current standards. This aspect is particularly valuable for companies looking to leverage existing cables while gradually upgrading their network capabilities.

The technology employed in the 10AUI/T includes advanced signal processing that ensures reliable data transmission, minimizing the impact of noise and interference commonly found in coaxial and twisted pair setups. With a maximum distance of up to 200 meters for 10BASE-T and 185 meters for 10BASE-2, the 10AUI/T is adept at handling a range of networking scenarios, adapting to specific needs and layouts.

In terms of ease of use, the 10AUI/T is notable for its plug-and-play setup. This feature accelerates deployment times, allowing IT professionals to install the converter with minimal configuration. The device is designed to be compact and efficient, making it suitable for environments with limited space. It requires minimal power, which not only cuts down operational costs but also promotes environmental sustainability.

The 10AUI/T is equipped with diagnostic LED indicators that provide real-time feedback on device status, connection quality, and data transmission activity. This allows network administrators to quickly identify any issues that may arise, leading to reduced downtime and enhanced network reliability.

In summary, the Omnitron Systems Technology 10AUI/T media converter stands out for its exceptional versatility, compatibility, and performance features. By providing a bridge between legacy coaxial and modern twisted pair Ethernet, it enables organizations to maximize their existing investments while paving the way for future upgrades. Its ease of installation, efficient design, and robust technology make the 10AUI/T an ideal choice for businesses looking to enhance their networking capabilities without sacrificing reliability or performance.
Top Page Image Contents