Omnitron Systems Technology T1 warranty Mounting instructions, Switch Settings, Mounting Options

FlexPointTM T1/E1 Copper to Fiber

Converters

User Instructions

Description:

The FlexPoint T1/E1 connects T1 and E1 devices, such as PBXs, CSUs and routers, via multimode (MM) or single-mode (SM) fiber. Designed to extend the standard T1/E1 twisted pair or Coax network distances over fiber, this converter provides protection from environmental noise and effectively increases high-speed network reliability. The following models are described here.

Model #	Fiber Type	Max Distance
4470/90-x	MM, SC, 1310nm	5km
4471/91-x	SM, SC, 1310nm	30km
4472/92-x	MM, ST, 1310nm	5km
4473/93-x	SM, ST, 1310nm	30km

Power Adapter Notice

1.When Using in a stand-alone configuration, this product is intended to be and must be used only with a Listed Direct Plug-In Power Unit marked “Class 2” and rated at 9VDC, 1 Amp.

2.This product should always be used only with Omnitron Supplied Power Unit model numbers 9113-PS or 9115-PS.

WARNING!

Before inserting the Power Adapter, verify that the power on the unit is appropriate for your AC line voltage source.

Mounting instructions:

The FlexPoint Fiber Converter can be solo-mounted using

awall-mounting kit, or rack-mounted using a 5-unit shelf, or a high-density FlexPoint 14-Unit Power-Redundant Chassis.

equipment. (The twisted pair connection requires two active pairs in a T1/E1 environment. The active pairs are pins 1&2 and pins 4&5. Only dedicated wire pairs should be used for the active pins.) Set the UTP DCE / DTE switch for the RJ-45/48 port to the appropriate setting.

Note: Use copper cables that are compliant with the specifications that are outlined in copper cable specifications.

Coax E1 Connector

Attach the BNC to the FlexPoint T1/E1 converter and attach the other end of the BNC to the network equipment.

Note: Use copper cables that are compliant with the specifications that are outlined in copper cable specifications.

Switch Settings:

UTP DCE/DTE setting

The UTP DCE/DTE switch is used to eliminate the need for crossover and custom cables to connect devices together when using the RJ-45/48 port. Set this switch to DCE to use a straight-through cable and to DTE when a crossover-cable would be required.

Line Type		Port Type	Distances
T1 DSX-1		RJ-45/48	0’ - 133’
T1 DSX-1		RJ-45/48	133’ - 266’
T1 DSX-1		RJ-45/48	266’ - 399’
T1 DSX-1		RJ-45/48	399’ - 533’
T1 DSX-1		RJ-45/48	533’ - 655’
T1 DS-1		RJ-45/48	0 dB
T1 DS-1		RJ-45/48	-7.5 dB
T1 DS-1		RJ-45/48	-15.0 dB
T1 DS-1		RJ-45/48	-22.5 dB
E1	75 Ω	Coax/BNC	Standard
E1	120 Ω	RJ-45/48	Standard
E1	75 Ω	Coax/BNC	Extended
E1	120 Ω	RJ-45/48	Extended

Switch Positions 1 2 3 4

L L L L L L L K L L K L L L K K L K L L

L L L L L K L K L K K L L K K K

K L L L K L L K K L K L K L K K

Local loop-back (L/LB)

This switch will set the FlexPoint T1/E1 converter in a loop-back mode on both the fiber and copper connections. By returning the switch to the normal position the unit will resume to normal operation.

Cu-Rx	FO-Tx
Cu-Tx	FO-Rx

Loopback Enabled

Remote loop-back (R+L/LB)

This switch will allow the entire fiber segment to be tested at either of the FlexPoint T1/E1 converters without having to set switches on both units. When set in this mode the local unit is switched to a local loop-back mode. The fiber Tx port will be further encoded to carry a remote loop-back protocol. This remote loop-back will set the far end FlexPoint T1/E1 converter to remote loop-back mode and

Warranty Registration http://www.omnitron-systems.com or complete both sides to: Technology, Inc. #500 _________________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ State: Zip Code: ________ _______________________________________________ Fax: _______________________ _________________________________________________ Please complete both sides of this form

4474/94-x SM, SC, 1310nm, LH 60km

Power Options (-x):

-0 No power adapter included (chassis module) -1 110 Volt / 60 Hz

-2 110-230 Volt / 50 Hz

Mounting Options

4380 FlexPoint Wall-Mounting Hardware Kit

4384 FlexPoint 18 to 72VDC Stand-Alone Power Supply 4381 FlexPoint DC Converter Wall-Mounting Kit (for 4384) 4385 FlexPoint 14-Unit 48VDC Power-Redundant Chassis 4392 FlexPoint 5-Unit Rack-Mounting Shelf

4395 FlexPoint 14-Unit AC Power-Redundant Chassis

Local loop-back and Remote loop-back

When both Local and Remote Loop-back are set to the Normal position, the FlexPoint T1/E1 uses the default B8ZS data format. When both switches are turned to their On position, it uses the AMI data format.

Transmit/force 1’s to fiber

This switch is used to insert an “all ones” pattern into the data stream being transmitted out of the fiber port on the FlexPoint T1/E1 converter. Data being received on the coax or twisted pair will be disabled and data being received on the fiber is passed through to the coax or twisted pair side. By returning the switch to the normal position the unit will resume to normal operation.

Transmit/force 1’s to Coax or UTP

This switch is used to insert an “all ones” pattern into the data stream being transmitted out of the coax or twisted pair on the FlexPoint T1/E1 converter. Data being received on the fiber will be disabled and data being received on the coax or twisted pair is passed through to the fiber side. By returning the switch to the normal position the unit will resume to normal operation.

Alarm Relay Contacts

The FlexPoint T1/E1 features dry relay contacts for optionally connecting the it into a separate T1/E1 alarm circuit. The relay closes when a loss of power or when signal detect is lost to the copper or fiber connection.

Relay	RJ-45/RJ-48
	3

6

Operational rating on relay pins 3 & 6: 0-220VDC max 2A

Fiber Optic Cable Attachment:

Connect the fiber cables between the FlexPoint T1/E1 converters. The transmit (Tx) must attach to the receive side and the receive (Rx) must attach to the transmit side.

Note: Use fiber cables that are compliant with the specifications that are outlined in fiber cable specifications.

Copper Cable Attachment:

RJ-45/RJ-48 T1/E1 connector

Connect to the RJ-45/48 connector on the FlexPoint T1/ E1 converter via a category 3 or better cable (Category 5 is recomended) and attach the other end to the network

LED Indicators

LED Color	Status	Description
Power:
Yellow	On	Power applied
Fiber:
Green	Off	No signal detect
	On	Signal detect
UTP/Coax:	Blink	All ones received
Green	Off	No signal detect
	On	Signal detect
Test:	Blink	All ones received
Green	Off	Normal operation
	On	L/LB or All 1’s Test mode
	Blink	R+L/LB Received master
	Fast Blink	R+L/LB Received slave

Fiber Cable Specifications:

Multimode

Cable:	50/125, 62.5/125, 100/140 μm
Wavelength:	1310nm
Max Distance:	5km
Singlemode
Cable:	9/125 μm
Wavelength:	1310nm
Max Distance:	30km
Singlemode long-haul
Cable:	9/125 μm
Wavelength:	1310nm
Max Distance:	60km

			DCE					DTE
	1					1
Twisted		RTIP		TTIP	Twisted		RTIP		TTIP
Pair #1	2	RRING		TRING	Pair #1	2	RRING		TRING
Twisted	4	TTIP		RTIP	Twisted	4	TTIP		RTIP
Pair #2	5	TRING		RRING	Pair #2	5	TRING		RRING

T1/E1 Copper line configuration settings

The T1/E1 copper line codes and line lengths are configured using dip switches located on the side of the FlexPoint T1/E1 media converter.

Copper Cable Specifications:

Twisted-Pair cable for T1

Gauge	22 to 24 AWG
Impedance	100 Ω + 10%
Impedance characteristic	2.6 dB / 100m @ 1.0 MHz
Maximum distance	6,000 ft
Twisted-Pair cable for E1
Gauge	22 to 24 AWG
Impedance	120 Ω + 10%
Impedance characteristic	2.6 dB / 100m @ 1.0 MHz
Maximum distance	8,000 ft
Coax cable for E1
Gauge	22 to 24 AWG
Impedance	75 Ω + 10%
Impedance characteristic	2 dB / 100m @ 1.0 MHz
Maximum distance	8,000 ft

For product specifications refer to the product data sheet.

Technical Support:

For help with this product, contact our Tech. Support:

Phone:	(949) 250-6510
Fax:	(949) 250-6514
Address: Omnitron Systems Technology, Inc.
	140 Technology Drive, #500
	Irvine, CA 92618 USA
E-mail:	support@omnitron-systems.com
URL:	http://www.omnitron-systems.com

Operational switch settings and functions

The following operational switches located on the front of the FlexPoint T1/E1 converter are to assist in installation and fault isolation.

	Local Dual Loop Back
Normal	Remote & Local Loop Back
	Force 1’s to Fiber
	Force 1’s Copper

Warning

The operating description in this Instruction Manual is for use by qualified personnel only. To avoid electrical shock, do not perform any servicing of this unit other than that contained in the operating instructions, unless you are qualified and certified to do so by Omnitron Systems Technology, Inc.

Caution

All user-required operations can be performed without opening the unit. Never attempt to open or remove the cover or tamper with the unit.

Warranty

This product is warranted to the original purchaser against defects in material and workmanship for a period of TWO YEARS from the date of shipment. A LIFETIME warranty may be obtained by the original purchaser by REGISTERING this product with Omnitron within 90 days from the date of shipment.

TO REGISTER, COMPLETE AND MAIL OR FAX THE REGISTRATION PORTION OF THIS INSTRUCTION MANUAL TO THE INDICATED ADDRESS. Or you may register your product on the Internet at http://www.omnitron- systems.com. During the warranty period, Omnitron will, at its option, repair or replace a product which is proven to be defective.

For warranty service, the product must be sent to an Omnitron designated facility, at Buyer’s expense. Omnitron will pay the shipping charge to return the product to Buyer’s designated US address using Omnitron’s standard shipping method.

return a signal to the sending unit. An LED on the local and remote FlexPoint T1/E1 converters will show a confirmation that the fiber segment is communicating properly between devices. By returning the switch to the normal position it will return to normal operation.

Cu-Rx	FO-Tx	FO-Rx	Cu-Tx
Cu-Tx	FO-Rx	FO-Tx	Cu-Rx

Remote Loop Request

Over Fiber

Limitation of Warranty

The foregoing warranty shall not apply to defects resulting from improper or inadequate use and/or maintenance of the equipmentbyBuyer,Buyer-suppliedequipment,Buyer-supplied interfacing, unauthorized modifications or tampering with equipment (including removal of equipment cover by personnel not specifically authorized and certified by Omnitron), or misuse, or operating outside the environmental specification of the product (including but not limited to voltage, ambient temperature, radiation, unusual dust, etc.), or improper site preparation or maintenance.

No other warranty is expressed or implied. Omnitron specifically disclaims the implied warranties of merchantability and fitness for any particular purpose.

Exclusive Remedies

The remedies provided herein are the Buyer’s sole and exclusive remedies. Omnitron shall not be liable for any direct, indirect, special, incidental, or consequential damages, whether based on contract, tort, or any legal theory.

Form: 040-04470-002D 11/07

User	Please register on-line @	and mail or fax this registration form	Omnitron Systems 140 Technology Drive, Irvine, CA 92618, USA	Fax: (949) 250-6514	Name:	Company:	Address:	City: ___________________	Country:	Phone: ____________________	E-mail:
User Warranty Registration	Please register on-line at http://www.omnitron-systems.comor complete both sides	and return this form to Omnitron Systems.	Model: _________________________________________________	Serial Number:Purchase Date: ______________	Purchased From: _________________________________________	Address: ______________________________________________	City:State: Zip Code: ________ Country: _______________________________________________	Comments and Suggestions: _______________________________	______________________________________________________	______________________________________________________	Please complete both sides of this form