Oreck 77224-01REVC Parts List, Assembly, Operating Instructions, General Information, Duster Loop

Parts List

To assist you in identifying components of your vacuum, the parts have been numbered as follows:

1	Helping Hand® handle with soft grip			1
2	On/off switch
3	Cord dump			2
4	Handle tube
				3
5	Bag stiffener
6	Deflector
7	Bag dock			4
8	Carry handle
9	Zipper
10	Bag clip		5
11	Headlight cover		6
12	Front light lens
13	Main bumper
14	Edge brush	33	7	8
15	Belt door
16	Power cord			9
17	Cord assembly
18	Handle collar
19	Connector assembly
20	Carry handle clamp
21	Collars
22	Lower tube		10
23	Bag clip clamp	11
24	Scent cartridge door
25	Fan housing	12
26	Rear wheels	13
27	Side light			15
28	Cover			14
29	Bag spring
30	Bag pocket
31	Outer bag
32	Power nozzle
33	Inner filter bag			17
34	Duster loop
		16
				18
		19
		8		31
		20		30
		21	22	34
			23	29
		24		28
		25		27
			26	14
				32

Assembly

fig. 1 With ON/OFF switch facing the front of the unit, align slots in handle tube with tabs in connector. Insert the handle tube into connector. Tighten collar at base of handle tube onto the connector until it locks, “snaps”.

fig. 2 Snap cord assembly into the cord clip located on the left side of

the collar. Leave excess cord at the power head to allow movement.

Operating Instructions

Make sure disposable paper filter dust bag is in place. DO NOT operate the cleaner without a paper filter dust bag. Plug the power cord into an electrical outlet and press the On Low (l) - On High (ll) - OFF(O) switch on handle assembly when ready to operate.

Up-Position Lock

fig. 3 Place foot on power head and lean handle back gently to release lock for vacuum use. Return handle to the full upright position to engage lock.

NOTE: Do not operate the unit while in the upright and locked position. Do not let the unit run while in any one stationary position for any period of time. Keep the unit moving while in operation.

Carry Handle

fig. 4 Raise the carry handle located on back of the unit for easy lifting, carrying, and stair vacuuming. Lower the handle during use to eliminate obstruction.

Duster Loop

fig. 5 For convenient use of dusters, a loop has been sewn onto the outer bag. This will allow easy removal and storage of the duster.

For Easy Power Cord Storage

fig. 6 Raise carrying handle and wrap power cord around carry handle and Helping Hand® handle.

fig. 7 To release cord, twist cord dump located on Helping Hand® handle 1/2 turn. Slide cord off handle. (fig. 8)

Cleaner Storage

Both the Helping Hand® handle and carry handle can be used for convenient, space saving storage of cleaner. Hang cleaner by carry handle on a sturdy fastener or Helping Hand® handle on a closet rod.

Operating Recommendations

This new ORECK XL21 High-Speed Upright is one of the finest, fastest, and strongest units in its class. You’ll love the way it cleans, gets under things, and it’s SO lightweight and easy to use.

The following are a few simple suggestions regarding its operation:

1.When inserting a new disposable paper filter dust bag—FIRST PUFF OUT and OPEN THE BAG.

2.When the disposable filter dust bag is full, REPLACE IT.

3.If at any time the machine does not pick up properly or makes an unusual noise, STOP OPERATION and service.

4.Although your upright will pick up pins, paper clips, and other small objects, it is recommended that these be removed from the floor before you vacuum. Failure to do so may result in permanent damage to the motor suction fan and its housing.

5.WARNING: Do not use your vacuum cleaner on damp or wet surfaces. This will cause damage to the vacuum cleaner and is dangerous to the user. Damage caused by use on wet or damp surfaces is not covered under warranty.

6.REPLACE THE BELT EVERY 6 MONTHS, SCENT CARTRIDGE EVERY MONTH, AND MOTOR FILTER EVERY 2 MONTHS.

7.Change the disposable filter dust bag at least once a month—even if it is not full! The collected dust in the dust bag can cause odor, attract moisture, and can affect the efficiency of the cleaner.

8.DO NOT run the vacuum cleaner over the cord. The revolving brush could damage the cord.

General Information

The performance of your new cleaner greatly depends upon care and maintenance. The instructions in this manual will guide you in performing basic care and maintenance. To obtain the most satisfying years of service read the instructions and keep them handy for future reference.

5