Daylight Projection Clock
Model: DP100
USER MANUAL
EN
INTRODUCTION
Thank you for selecting the Oregon ScientificTM daylight projection clock (DP100).
NOTE Please keep this manual handy as you use your new product. It contains practical step-by-step instructions, as well as technical specifications and warnings you should know about.
OVERVIEW
FRONT VIEW
1
6
3
4
1.CDS light sensor: Adjusts projection brightness
2.ALARM ON / OFF: Activate / deactivate alarm
3.LCD display: Clock, alarm, calendar and indoor temperature
4.
: Alarm icon
5.IR motion sensors: Snooze; change display mode
6.Projector: Projects time, alarm status and indoor temperature
BACK AND BASE VIEW
1
5
10
1.FOCUS: Focus the projected image
2.Temperature sensor and adapter slot
3.CLOCK: Enter clock setting mode
4./ : Increase / decrease setting
5.PROJECTION OFF / CLOCK / AUTO: Select projection mode
6.ALARM: Enter alarm setting mode
7.180° ROTATION: Rotate projection image by 180°
8.°C / °F: Select temp erature unit
9.RESET: Return to default settings
10.CDS ON / OFF: Activate light sensor
GETTING STARTED
ADAPTER
Insert the adapter into the adapter slot as shown.
CLOCK
To set the clock:
1.Press and hold CLOCK for 2 seconds. The setting will blink.
2. Use / to change the setting.
3.Press CLOCK to confirm.
4.The settings order is: 12 / 24 hour format, hour, minute, year, month-day format, month and day.
LCD DISPLAY
Use motion above the IR motion sensors to toggle display mode between:
•Clock
•Calendar
•Alarm
•Indoor temperature
NOTE The IR motion sensors range is from 2.5 to 15 cm (1 to 6 in) above the sensor. Any movement outside this
range will not be detected.
ALARM
To set the alarm:
1.Press ALARM or navigate to Alarm display.
2.Press and hold ALARM for 2 seconds to enter alarm setting mode. The setting will blink.
3. Use / to change the setting for hour.
4.Press ALARM to confirm.
5.Repeat steps 3 and 4 to set minute. 
appears when the alarm is set.
To silence the alarm:
•Use motion above the IR motion sensors to activate the 8-minute SNOOZE feature.
OR
• Press ALARM, CLOCK, or to mute the alarm and automatically activate the alarm again after 24 hours.
To activate / deactivate the alarm:
•Press ALARM ON / OFF.
PROJECTION
The ultra-bright LED enables daylight projection of time and temperature information.
To activate projection:
Slide PROJECTION to AUTO or CLOCK.
•Slide to AUTO to toggle between current time and indoor temperature.
•Slide to CLOCK to project current time only.
To adjust the projection image:
•Switch CDS to ON to activate automatic projection dimming.
•Press 180° ROTATION to rotate the image by 180°.
•Focus the projector image by turning the FOCUS wheel.
NOTE Please take care not to look into the projector. Oregon Scientific will not be held responsible for any results or consequences arising from the misuse of this product.
TEMPERATURE
Press °C / °F to select the temperature display unit.
RESET
To return the unit to the default settings, insert a thin blunt object into the RESET hole.
PRECAUTIONS
This product is engineered to give you years of satisfactory service if you handle it carefully. Here are a few precautions:
•Do not cover the ventilation holes. Make sure items that are nearby such as newspapers, tablecloths, curtains etc cannot accidentally cover the ventilation holes.
•Placement of this product on wood surfaces with certain types of finishes, such as clear varnish, may result in damage to the finish. Consult the furniture manufacturer’s care instructions for direction as to the types of objects that may safely be placed on the wood surface. Oregon Scientific shall not be responsible for any damage to wood surfaces from contact with this product.
•Do not immerse the unit in water. If you spill liquid over it, dry it immediately with a soft, lint-free cloth.
•Do not clean the unit with abrasive or corrosive materials. This may scratch the plastic parts and corrode the electronic circuit.
•Do not subject the unit to excessive force, shock, dust, temperature or humidity, which may result in malfunction, shorter electronic life span, damaged battery and distorted parts.
•Do not tamper with the unit’s internal components. Doing so will invalidate the warranty on the unit and may cause unnecessary damage. The unit contains no user-serviceable parts.
•Do not dispose this product as unsorted municipal waste. Collection of such waste separately for special treatment is necessary
•Due to printing limitations, the displays shown in this manual may differ from the actual display.
•The contents of this manual may not be reproduced without the permission of the manufacturer.
NOTE The technical specifications for this product and the contents of the user manual are subject to change without notice.
SPECIFICATIONS | |
TYPE | DESCRIPTION |
Unit dimension | 138 x 88 x 44 mm |
(H x W x D) | (5.4 x 3.5 x 1.7 in) |
Unit weight | 523g (18.4 oz) |
Clock format | 12 / 24-hour |
Alarm duration | 2 min |
Snooze | 8 min |
Temperature range | 0°C to 50°C |
| (32°F to 122°F) |
Temperature resolution | 1°C (1°F) |
Projector rotation angle | + / - 90° |
IR sensor coverage distance | 2.5 to 15 cm |
| (1 to 6 in) |
Power | DC 5.0V adapter |
ABOUT OREGON SCIENTIFIC
Visit our website (www.oregonscientific.com) to learn more about Oregon Scientific products such as digital cameras; MP3 players; children’s electronic learning products and games; projection clocks; health and fitness gear; weather stations; and digital and conference phones. The website also includes contact information for our Customer Care department in case you need to reach us, as well as frequently asked questions and customer downloads.
We hope you will find all the information you need on our website, however if you’re in the US and would like to contact the Oregon Scientific Customer Care department directly, please visit:
www2.oregonscientific.com/service/default.asp
OR
Call 1-800-853-8883.
For international inquiries, please visit: www2.oregonscientific.com/about/international.asp
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and
(2)This device must accept any interference received, including interference that may cause undesired operation.
WARNING Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio / TV technician for help.
DECLARATION OF CONFORMITY
The following information is not to be used as contact for support or sales. Please call our customer service number (listed on our website at www.oregonscientific.com), or on the warranty card for this product) for all inquiries instead.
We | |
Name: | Oregon Scientific, Inc. |
Address: | 19861 SW 95th Ave., |
| Tualatin, Oregon 97062 USA |
Telephone No.: | 1-800-853-8883 |
declare that the product
Product No.: | DP100 |
Product Name: | Daylight Projection Clock |
Manufacturer: | IDT Technology Limited |
Address: | Block C, 9/F, Kaiser Estate, |
| Phase 1,41 Man Yue St., Hung |
| Hom, Kowloon, Hong Kong |
is in conformity with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference. 2) This device must accept any interference received, including interference that may cause undesired operation.
FR
INTRODUCTION
Merci d’avoir sélectionné l’Horloge à Projection de Jour de Oregon ScientificTM. (Modèle DP100).
REMARQUE Veuillez conserver ce manuel pour toutes références ultérieures. Il contient toutes les instructions pratiques, les caractéristiques techniques et les avertissements à prendre en compte.
VUE D’ENSEMBLE
FACE AVANT
1
6
3
4
1.Capteur de lumière CDS: Ajuste la clarté de projection
2.ALARM ON / OFF: Permet d’activer / désactiver l’alarme
3.Affichage LCD: Horloge, alarme, calendrier et température intérieure.
4.
: Icône de l’alarme
5.Capteurs de mouvement infra rouge: Snooze (Rappel d’alarme) ; changement du mode d’affichage
6.Projecteur: Permet de projeter l’heure, l’état de l’alarme et la température intérieure
VUE DE DOS ET VUE INFERIEURE
1
5
10
1.FOCUS: Permet de mettre au point l’image du projecteur
2.Capteur de température et prise adaptateur
3.CLOCK: Permet d’entrer dans le mode réglage de l’horloge
4./ : Permet d’augmenter / diminuer les valeurs de réglage.
5.PROJECTION OFF / CLOCK / AUTO: Permet de sélectionner le mode de projection
6.ALARM: Permet d’entrer dans le mode réglage de l’alarme
7.180° ROTATION: Permet de faire tourner l’image à 180°
8.°C / °F: Permet de sélectionner l’unité de mesure de la température
9. RESET: Permet de revenir aux réglages par défaut
10.CDS ON / OFF: Permet d’activer le capteur de lumière
AU COMMENCEMENT
ADAPTATEUR
Branchez l’adaptateur dans la prise adaptateur comme indiqué.
HORLOGE
Pour régler l’horloge :
1.Appuyez et maintenez enfoncée la touche CLOCK pendant 2 secondes. Le réglage clignotera.
2. Utilisez / pour changer le réglage
3.Appuyez sur CLOCK pour confirmer.
4.L’ordre de réglage est le suivant : Format 12/24 heures, heure, minutes, année, format mois/jour, mois et jour.
AFFICHAGE LCD
Utilisez le signe situé au dessus des capteurs de mouvement infra rouge pour alterner entre les modes suivants :
•Horloge
•Calendrier
•Alarme
•Température intérieure
REMARQUE La portée des capteurs de mouvement infra rouge est de 2,5 à 15 cm (1 à 6 pouces) au dessus du capteur. Tout mouvement hors de cette portée ne sera pas détecté.
ALARME
Pour régler l’alarme :
1.Appuyez sur ALARM ou entrez dans l’affichage de l’Alarme
2.Appuyez et maintenez enfoncée la touche ALARM pendant 2 secondes pour entrer dans le mode de réglage de l’alarme. Le réglage clignotera.
3. Utilisez | / pour changer le réglage de l’heure |
4.Appuyez sur ALARM pour confirmer.
5.Répétez les étapes 3 et 4 pour régler les minutes 
s’affichera une fois l’alarme réglée.
Pour couper le son de l’alarme :
•Utilisez le signe situé au dessus des capteurs de mouvement infra rouge pour activer la fonction SNOOZE (rappel d’alarme) de 8 minutes.
OU
• Appuyez sur ALARM, CLOCK, ou pour couper le son de l’alarme et la réactiver automatiquement 24 h plus tard.
Pour activer / désactiver l’alarme :
•Appuyez sur ALARM ON / OFF.
PROJECTION
La forte clarté de la diode électroluminescente permet une projection en journée de l’heure et de la température.
Pour activer la projection :
Placez l’encoche PROJECTION sur AUTO ou sur
CLOCK.
•Placez l’encoche sur AUTO pour alterner entre l’heure actuelle et la température intérieure.
•Placez l’encoche sur CLOCK pour ne projeter que l’heure actuelle.
Pour ajuster l’image projetée :
•Placez CDS sur ON pour activer la gradation de projection automatique.
•Appuyez sur 180° ROTATION pour faire tourner l’image à 180°.
•Tournez la molette FOCUS pour mettre au point l‘image projetée.
REMARQUE Faîtes attention à ne pas regarder dans le projecteur. Oregon Scientific ne sera en aucun cas responsable des conséquences ou résultats découlant de la mauvaise utilisation de ce produit.
TEMPERATURE
Appuyez sur °C / °F pour sélectionner l’unité d’affichage de la température.
