Oregon Scientific ATC5K manual IX Connecting to a computer

ATC5K_manual-US0710.qxd 8/18/08 5:40 PM Page 9

Setting the Date

When adjusting the date, “DD” will be shown. Press the “Menu button” to

adjust the date. Press the 'Confirm' button to verify, after which you would be able to proceed to setting the time.

Setting the Time

Press the “Menu button” to adjust the hour. Press the “Confirm” button to verify the hour, after which you would be able to proceed to setting the minute.

Press the “Menu button” to adjust the minute. Press the “Confirm” button

to verify the time and exit this mode. Note: Time will be shown in 24 hour format.

Deleting individual files

The Delete icon looks like this . Once inside the delete menu to delete the last file that was recorded, press the Menu button until the LCD screen shows . Press the Confirm button to confirm.

Repeat these two steps to individually delete your files.

Note: After file deletion, the LCD screen will adjust the remaining number of files accordingly.

Delete All files

To delete all files stored in your camera, press the Menu button until the

LCD screen shows . Press the Confirm button to verify. Note: It may take a few minutes to delete multiple files at one time.

SD Memory Card

In this unit, you can use SD Memory Cards of up to 4GB.

To use an SD memory card, turn off the ATC5K and insert the SD memory card. When the camera is turned on again the SD card icon SD will be displayed on the LCD screen.

The remaining time on the SD card will also be displayed on the LCD screen. All of the video footage will now be saved onto the SD card.

Note:

1. If there is an error on the SD memory card, the SD card icon and the

letters “Err” will be displayed on the LCD screen. In this case, turn off the

camera and remove the SD card.

2. The SD card is equipped with a Write-Protect switch that can prevent

Available Recording Time

The available recording time is an approximation (these vary depending on the recording conditions and the type of card).

Picture quality		VGA	QVGA
setting		30 fps	30 fps
Internal	32 MB	47 s	1min36s
Memory
SD	1 GB	30 min	57 min
Memory	2 GB	60 min	114 min
Card
	4 GB	120 min	216 min

IX) Connecting to a computer

You can upload your recorded video footage to a PC by connecting the ATC5K to your PC using the USB cable. 1. Turn the ATC5K on.

2. Connect the ATC5K to a PC via the USB cable.

3.There are 2 modes available, File and Cam . File allows you to check the files in the camera or SD card. Cam is the webcam function.

4.Select Cam to use the ATC5K as a webcam by pressing "Confirm" whilst the icon is highlighted. Please note that the software must be installed before using the webcam mode.

5.“File” appears on the ATC5K LCD screen, which means ATC5K is connected to your PC and files are available for review.

6.To choose to review Files in the Camera/SD card the user should press “Confirm” . Once selected the ATC5K drive appears in the [My Computer] folder.

*If you are connecting the camera to a PC for the first time, the required driver is installed automatically so that the camera can be recognized by Windows Plug and Play. The 100ATC5K drive then appears on the [My Computer] folder.

7.Open the “100ATC5K” folder in the [DCIM] folder to start selecting your desired video files. Copy the desired video to your PC.

• Folder Composition:

	writing and formatting to the card. “Card Locked” will be displayed if
	the SD card is locked with Write-Protect switch.
3.	We recommend using SanDisk regular or AData SD cards.
4.	With use on Windows 2000 users must format to FAT otherwise the SD

card and camera may malfunction.

913

Removable disk

•Internal Memory

•SD Memory Card

DCIM

100ATC5K

AVI_0001

AVI_0002

AVI_0003

914