the R.A.
Optional Motor Drives for Automatic Tracking
An optional DC motor drive can be mounted on the R.A. axis of the equatorial mount to provide
Understanding the Setting Circles
The setting circles on an equatorial mount enable you to locate celestial objects by their “celestial coordinates”. Every object resides in a specific location on the “celestial sphere”. That location is denoted by two numbers: its right ascension (R.A.) and declination (Dec.). In the same way, every loca‑ tion on Earth can be described by its longitude and latitude. Right ascension is similar to longitude on Earth, and declina‑ tion is similar to latitude. The R.A. and Dec. values for celestial objects can be found in any star atlas or star catalog.
The R.A. setting circle (Figure 11) is scaled in hours, from 1 through 24, with small marks in between representing 10- minute increments (there are 60 minutes in 1 hour of right ascension). The lower set of numbers apply to viewing in the Northern Hemisphere, while the numbers above them apply to viewing in the Southern Hemisphere.
The Dec. setting circle (Figure 11) is scaled in degrees, with each mark representing 2° increments. Values of declination coordinates range from +90° to
So, the coordinates for the Orion Nebula listed in a star atlas will look like this:
R.A. 5h 35.4m Dec. –5° 27'
That’s 5 hours and 35.4 minutes in right ascension, and
Before you can use the setting circles to locate objects, the mount must be accurately polar aligned, and the setting cir‑ cles must be calibrated.
Calibrating the Declination Setting Circle
1.Loosen the Dec. lock lever and position the telescope as accurately as possible in declination so it is parallel to the R.A. axis as shown in Figure 1.
2.Loosen one of the thumbscrews on the Dec. setting circle, this will allow the setting circle to rotate freely. Rotate the Dec. setting circle until the pointer reads exactly 90°. Re- tighten the setting circle thumbscrew.
Dec.
setting circle
Dec. |
|
|
| R.A. | ||
setting circle |
|
|
| setting | ||
thumbscrew |
|
|
| circle | ||
| ||||||
(2) |
|
|
|
|
|
|
Dec. |
|
|
|
| ||
indicator |
|
|
|
|
| |
|
|
|
|
| ||
arrow |
|
|
|
| ||
R.A. |
|
|
|
| ||
indicator |
|
|
|
| R.A. setting circle | |
|
|
|
| |||
arrow |
|
|
| thumbscrew (2) | ||
Figure 11. The R.A. and Dec. setting circles.
Calibrating the Right Ascension Setting Circle
1.Identify a bright star in the sky near the celestial equa‑ tor (declination = 0°) and look up its coordinates in a star atlas.
2.Loosen the R.A. and Dec. lock levers on the equatorial mount, so the telescope optical tube can move freely.
3.Point the telescope at the bright star whose coordinates you know. Lock the R.A. and Dec. lock levers. Center the star in the telescope’s field of view with the
4.Loosen one of the R.A. setting circle thumbscrews; this will allow the setting circle to rotate freely. Rotate the set‑ ting circle until the R.A. indicator arrow points to the R.A. coordinate listed in the star atlas for the object.
Finding Objects With the Setting Circles
Now that both setting circles are calibrated, look up in a star atlas the coordinates of an object you wish to view.
1.Loosen the Dec. lock lever and rotate the telescope until the declination value from the star atlas matches the read‑ ing on the Dec. setting circle. Remember that values of the Dec. setting circle are positive when the telescope is point‑ ing north of the celestial equator (Dec. = 0°), and negative when the telescope is pointing south of the celestial equa‑ tor. Retighten the lock lever.
2.Loosen the R.A. lock lever and rotate the telescope until the right ascension value from the star atlas matches the reading on the R.A. setting circle. Remember to use the lower set of numbers on the R.A. setting circle. Retighten the lock lever.
Most setting circles are not accurate enough to put an object
10
