C2R-CHY4
Radio Replacement Interface with Nav Outputs for all Chrysler Dodge / Jeep CANbus Vehicles With or Without Premium Audio Systems
VPW | Arbitration | Class 2 | J1850 |
| |||
1 0 0 0 1 1 1 0 1 1 1 1 0 0 1 0 0 1 1 0 1 1 0 0 |
Class 2 | EOD | J1850 | CRC |
1 1 1 0 1 0 0 0 0 1 1 0 1 1 0 1 1 1 0 0 1 1 0 0
Class 2 | J1850 | Class 2 |
1 0 0 0 1 1 1 0 1 1 1 1 0 0 1 0 0 1 1 0 1 1 0 0 | 1 1 1 0 1 0 0 0 0 1 1 0 1 1 0 1 1 1 0 0 1 1 0 0 |
Radio Connection Chart:
(Read the Installation Notes before making connections to the provided radio harness)
Yellow | Battery +12v |
Black | Ground |
Blue | Antenna On Input |
White | Front L + input |
White / Black | Front L - input |
Grey | Front R + input |
Grey / Black | Front R - input |
Green | Rear L + input |
Green / Black | Rear L - input |
Purple | Rear R + input |
Purple / Black | Rear R - input |
CAN Interface Connection Chart:
Red | Acc. Output (1 amp) |
Red / White | P.B. Output |
Purple / White | VSS Output (Pulse) |
Orange / White | Illum. Output (+) |
Green | Reverse Output (+) |
White / Green | SWC Output |
Blue / White | Amp Turn On Input |
| Navigation outputs and |
|
| Amplifier Remote Input |
|
| See Chart for wire color |
|
| descriptions. |
|
Radio Connections. See aside |
|
|
Chart for color description. |
| 1 |
| CAN | 4 3 2 |
Accessory Output +12volts 1amp max. | INTERFACE | 109 8 7 6 5 |
|
| Ch |
|
| 11 |
2 | 3456 2 1 |
|
Interface.SWC Programfor Version | Radio Specific Steering | |
|
| |
|
| Wheel Control Interface |
| 8 7 | (Sold Separately) |
| Program SWC | |
| 10 | Interface for Version 2. |
| 9 |
|
| 11 |
|
Installation Notes:
1.Only one of the two provided radio harnesses will be used. Remove the factory installed radio to determine the correct harness for your particular vehicle.
2.Vehicles without a factory amplifier: Connect the aftermarket radio’s front and rear speaker wires to the 22 pin plug.
3.Vehicles with a factory amplifier: The factory amplifier only accepts two audio channels (left and right). The amplifier’s fading is controlled by data communication from the factory radio.
The aftermarket radio does not have the ability to control the amplifier’s fader. Connect the front
outputs of the aftermarket radio to the rear inputs of the 22 pin radio connector. This will
allow navigation voice prompts and Bluetooth calls to be heard. The rear speaker outputs of the aftermarket radio are not used.
4.Vehicles with a manual transmission will not support a reverse trigger output.
5.The accessory output wire is located on the 11 pin CAN INTERFACE harness - connect this wire to the radio’s accessory wire. The accessory wire supplies +12v, 1 amp max when key is in the accessory or ignition position (fig. 1: If more current is needed).
6. 11 pin plug (to CAN INTERFACE):
1. Blue/White - Connect this wire to the radio’s amplifier remote output. Connect this wire with or without OEM amp present!
2. White/Green - SWC output.
3. Green - Connect this wire to the radio’s reverse input wire only.
4. Orange/White - Connect this wire to the radio’s Illumination input wire only.
5. Violet/White - Connect this wire to the radio’s VSS input wire only.
6.Red/White - Connect this wire to the radio’s parking brake input wire only.
Note: Do not connect these wires to any circuit other than the radio’s wire harness. | 12v Acc. |
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
| |||
85 87 | 86 |
| |||||||||
7. 11 pin plug (to SWC INTERFACE): | Ground | ||||||||||
From |
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
| ||||
This is a quick connection to a radio specific SWC interface. No additional connections are |
|
|
| 87a |
| ||||||
Interface |
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
| |||
necessary other than radio control connections. Plug the radio specific SWC interface in to |
|
|
|
|
|
| 30 |
|
| ||
|
|
|
|
|
|
|
| ||||
this connector and program the radio specific SWC interface for version 2. Do not cut the |
|
|
|
|
|
| |||||
Diode 1N4005 |
|
|
|
|
|
|
|
|
| ||
loops. Refer to the SWC interface instruction manual for the radio specific control function |
|
|
|
|
|
|
|
|
| ||
or equivelant |
|
| New High | ||||||||
programming order. |
|
|
| Current Output |
8.Refer to the aftermarket radio’s instruction manual for testing VSS, Reverse, Parking Brake and Illumination outputs. For the most current and
DISCLAIMER: Under no circumstances shall the manufacturer or the distributors of the
Pacific Accessory Corporation - Santa Ana, CA 92705 | ||
|