PAC C2R-VW2 instruction manual Radio Connection Chart, Installation Notes

C2R-VW2

Radio Replacement Interface with Nav Outputs for select Volkswagen CANbus Vehicles With or Without Premium Audio Systems

VPW	Arbitration	Class 2	J1850
1 0 0 0 1 1 1 0 1 1 1 1 0 0 1 0 0 1 1 0 1 1 0 0

Class 2 EOD J1850 CRC

1 1 1 0 1 0 0 0 0 1 1 0 1 1 0 1 1 1 0 0 1 1 0 0

Class 2	J1850	Class 2
1 0 0 0 1 1 1 0 1 1 1 1 0 0 1 0 0 1 1 0 1 1 0 0	1 1 1 0 1 0 0 0 0 1 1 0 1 1 0 1 1 1 0 0 1 1 0 0

Radio Connection Chart:
(Read the Installation Notes before making
connections to the provided radio harness)			Navigation outputs and
Yellow	Battery +12v
			Amplifier Remote Input
Black	Ground		See Chart for wire color
			descriptions.
Blue	Amp Turn On Input
White	Front L + input	Radio Connections. See aside
		Chart for color description.	CAN	1
White / Black	Front L - input	AccessoryOutput +12volts1ampmax.		4 3 2
Grey / Black	Front R - input		INTERFACE	8910 7 6 5
Grey	Front R + input
Green	Rear L + input			11
Green / Black	Rear L - input
Purple	Rear R + input	2
Purple / Black	Rear R - input	Interface.SWC VersionforProgram	234561	Radio Specific Steering
				Wheel Control Interface
CAN Interface Connection Chart:			89 7	(Sold Separately)
				Program SWC
Red	Acc. Output (1 amp)		10	Interface for Version 2.
			11
Red / White	P.B. Output (-)	Installation Notes:
Purple / White	VSS Output (Pulse)	For the most current and up-to-date application guide please visit www.pac-
		audio.com
Orange / White	Illum. Output (+)
Green	Reverse Output (+)	1. Vehicles with or without a factory amplifier: Connect the aftermarket radio’s
White / Green	SWC Output	front and rear speaker wires to the 16 pin plug.
		2. The accessory output wire is located on the 11 pin CAN INTERFACE harness

	- connect this wire to the radio’s accessory wire. The accessory wire supplies
	+12v, 1 amp max when key is in the	Fig. 1
accessory or ignition position (see fig. 1: If more current is needed).				High Current 12v
		(using a SPDT relay)
						(Fused)
3. 11 pin plug (to CAN INTERFACE):
1.	White/Green - SWC output.	12v Acc.
			85 87				86
2.	Green - Connect this wire to the radio’s reverse input wire only.	From						Ground
					87a
3.	Orange/White - Connect this wire to the radio’s Illumination input wire only.	Interface
4.	Violet/White - Connect this wire to the radio’s VSS input wire only.					30
5.	Red/White - Connect this wire to the radio’s parking brake input wire only.	Diode 1N4005		New High
	Please Note: The parking brake wire will output a neg (-) trigger at all	or equivelant

times until the vehicle is moving at a speed of approximately 3 mph or	Current Output
faster.

Note: Do not connect these wires to any circuit other than the aftermarket radio’s wire harness.

4.11 pin plug (to SWC INTERFACE):

This is a quick connection to a radio specific SWC interface. No additional connections are necessary other than radio control connections. Plug the radio specific SWC interface in to this connector and program the radio specific SWC interface for version 2. Do not cut the loops. Refer to the SWC interface instruction manual for the radio specific control

function programming order.

5. Refer to the aftermarket radio’s instruction manual for testing VSS, Reverse, Parking Brake and Illumination outputs.

DISCLAIMER: Under no circumstances shall the manufacturer or the distributors of the C2R-VW2 be held liable for consequential damages sustained in connection with the C2R-VW2. The manufacture and it’s distributors will not, nor will they authorize any representative or any other individual to assume obligation or liability in relation to the C2R-VW2 other than its replacement.

01-04-10	Pacific Accessory Corporation - Santa Ana, CA 92705
	techsupport@pac-audio.com • Voice: 866-931-8021 • Fax: 714-835-3233 • www.pac-audio.com