PAC Car Amplifier manual JBL Amplifier Turn-On Interface for Toyota CANbus Vehicles

TATO

JBL Amplifier Turn-On Interface for Toyota CANbus Vehicles

VPW	Arbitration	Class 2	J1850
1 0 0 0 1 1 1 0 1 1 1 1 0 0 1 0 0 1 1 0 1 1 0 0

Class 2 EOD J1850 CRC

1 1 1 0 1 0 0 0 0 1 1 0 1 1 0 1 1 1 0 0 1 1 0 0

Class 2	J1850	Class 2
1 0 0 0 1 1 1 0 1 1 1 1 0 0 1 0 0 1 1 0 1 1 0 0	1 1 1 0 1 0 0 0 0 1 1 0 1 1 0 1 1 1 0 0 1 1 0 0

The TATO is designed to control the power and audio levels of the factory installed JBL amplifier allowing the OEM radio to be removed and replaced with an aftermarket stereo.

Installation:

Note: BEFORE REMOVING THE FACTORY RADIO: BALANCE AND FADE IT TO THE CENTER, TURN THE RADIO UP TO AT LEAST 3/4 VOLUME, TURN THE RADIO OFF, TURN THE IGNITION OFF & THEN PROCEED WITH REMOVING THE FACTORY RADIO

Disconnect the factory radio from the OEM wiring harness and remove it from the vehicle. Make the following connections of the TATO wiring harness to the aftermarket radio:

Connections:
• Yellow Wire	- Connect to 12 Volt Constant Power on aftermarket radio
• Red Wire	- Connect to Accessory on aftermarket radio
• Black Wire	- Connect to Ground on aftermarket radio
• Orange/White Wire	- Connect to Dimmer on aftermarket radio
• *11 Pin Harness	- Connect to PAC’s SWI-X, SWI-JACK, SWI-PS or SWI-ECL2 (Sold Separately)
Red Bullet Connector	- Connect to Accessory
Black Bullet Connector	- Connect to Ground

•Connect the 4 RCA connectors to the RCA outputs of the aftermarket radio

Front Left - White RCA	Front Right - Grey RCA
Rear Left - Green RCA	Rear Right - Purple RCA

If connecting the TATO to a head unit with only 2 Channel RCA outputs, use two pairs of RCA splitters (1M-2F) to split the signal. Failure to connect all 4 inputs of the TATO will result in loss of audio performance. Fade audio controls will only function with a 4 channel aftermarket deck.

Connections to the TATO Interface:

• Connect 24-pin translucent connector to the side of the TATO.

•Connect 8-pin DIN cable to the plug on the side of the TATO.

Connections to the Vehicle:

•Plug the main 20-pin Toyota harness into the matching factory wir- ing harness.

•*If using PAC’s SWI-X,SWI-JACK,SWI-PS or SWI-ECL2, Plug the smaller 20-pin harness into the matching factory wiring har- ness. Program PAC’s SWI-X, SWI-JACK, SWI-PS or SWI-ECL2 for version #8 and follow the programming instructions included with PAC’s SWI-X, SWI-JACK, SWI-PS or SWI-ECL2.

DISCLAIMER: Under no circumstances shall the manufacturer or the distributors of the TATO be held liable for consequential damages sustained in connection with the TATO. The manufacture and it’s distributors will not, nor will they authorize any representative or any other individual to assume obligation or liability in relation to the TATO other than its replacement.

06-29-10	Pacific Accessory Corporation - Santa Ana, CA 92705
	866-931-8021 • www.pac-audio.com